Rockwell Automation 8520-9API 9/Series OCI API Developer's Guide - Manual (Page 198)

OCI Data Items A–10
Publication 8520-6.6. - August 1999
Control Type Req Dual
Proc.
Units
Dependency
Units Array Indices Num
Indices
OCI/9/PC Data Type Description Item (Name)
93 TOOL_LENGTH_GEOM_
OFFSETS
Tool Length Geometry Offset LREAL [ ] [ ] Both 2 Offset Num, Num
Axes
Inch/MetĆ
ric/DeĆ
grees
TOOL_ENTRY_UN
ITS [ Tool_number
]
Yes R/W Lathe, Mill
92 TOOL_LENGTH_WEAR_
OFFSETS
Tool Length Wear Offset LREAL [ ] [ ] Both 2 Offset Num, Num
Axes
Inch/MetĆ
ric/DeĆ
grees
TOOL_ENTRY_UN
ITS [ Tool_number
]
Yes R/W Lathe, Mill
98 TOOL_ORIENTATION Tool Orientation Direction INT [ ] Both 1 Offset Num Yes R/W Lathe, Grinder
95 TOOL_RADIUS_GEOM_
OFFSETS
Tool Radius Geometry Offset LREAL [ ] Both 1 Offset Num Inch/MetĆ
ric/DeĆ
grees
TOOL_ENTRY_UN
ITS [ Tool_number
]
Yes R/W Lathe, Mill
94 TOOL_RADIUS_WEAR_
OFFSETS
Tool Radius Wear Offset LREAL [ ] Both 1 Offset Num Inch/MetĆ
ric/DeĆ
grees
TOOL_ENTRY_UN
ITS [ Tool_number
]
Yes R/W Lathe, Mill
96 WHEEL_GEOM_OFFSETS Wheel Geometry Offset LREAL [ ] [ ] Both 2 Offset Num, Num
Axes
Inch/MetĆ
ric/DeĆ
grees
TOOL_ENTRY_UN
ITS [ Tool_number
]
No R/W Grinder
l Operating Mode
46 ACTIVE_MODE Active Mode UINT enumerated
PAL
Both 0 Yes R All Controls
50 ACTIVE_SCALE_INDICATOR Active Scaling Indicator on Scaled Axes DINT Both 0 Yes R All Controls
31 ACTIVE_UNITS Inch/Metric Mode UINT enumerated Both 0 Yes R All Controls
54 AXIS_RAD_DIA_MODE Axis Radius/Diameter mode DINT bit pattern Both 0 Yes R Lathe/Cyl
m PAL/Logic Data
%...................
I/O Variables (%variables) UINT [ ] OCI No PAL
Prot
All Controls
!.......................
User defined PAL globals (!variables) UINT [ ] OCI No PAL
Prot
All Controls
$......................
System defined PAL globals ($variables) UINT [ ] Both PAL
Spec
PAL
Prot
All Controls
298
BLOCK_TRANSFER_READ_ DATA
Block transfer read data ($ARST) INT [ ] OCI 1 MAX_BLOCK_TRANSFER No R All Controls
299
BLOCK_TRANSFER_WRITE_ DATA
Block transfer write data ($AWST) INT [ ] OCI 1 MAX_BLOCK_TRANSFER No R All Controls
152 FG_CRITICAL_AVERAGE Critical Foreground Average UINT OCI 0 usec No R All Controls
153 FG_CRITICAL_MAX Critical Foreground Maximum UINT OCI 0 usec No R All Controls
154 FG_TOTAL_AVERAGE Total Foreground Average UINT OCI 0 usec No R All Controls
155 FG_TOTAL_MAX Total Foreground Maximum UINT OCI 0 usec No R All Controls
192 MEMORY_DUMP_ADDRESS Memory dump start address
(debug monitor)
DINT OCI 0 No R/W All Controls