Rockwell Automation 8520-9API 9/Series OCI API Developer's Guide - Manual (Page 210)

OCI Commands B–2
Publication 8520-6.6. - August 1999
Inst
ID
P3 type Parameter 3 P2 type Parameter 2 P1 type Parameter 1 Dual
Proc.
# Params OCI / 9/PC Control Type Command Description Item (Name)
60 TRANSFER_AXISCAL_TO_PORTA Axis calibration to port A All Controls OCI No
66 TRANSFER_AXISCAL_TO_PORTB Axis calibration to port B All Controls OCI No
Communications
88 ACTIVATE_RIO_PASSTHROUGH Activates remote I/O passthrough All Controls OCI No
113 AUX_COM_ABORT_COMMAND Aborts Aux Comm command in progress All Controls OCI No
82 AUX_COM_BACKUP_CONFIG_TABLE Aux Comm backup communication tables All Controls OCI 1 No File Name STRING1
78 AUX_COM_CMD_FWD_SEARCH Aux Comm command forward search All Controls OCI 2 No Search Type enum DINT Search String STRING1
79 AUX_COM_CMD_REV_SEARCH Aux Comm command reverse search All Controls OCI 2 No Search Type enum DINT Search String STRING1
150 AUX_COM_CMDTBL_FROM_FLASH Reads command table from flash All Controls OCI No
81 AUX_COM_CMDTBL_TO_FLASHH Writes command table to flash All Controls OCI No
149 AUX_COM_CONFIG_FROM_FLASH Read Aux Comm configuration from flash All Controls OCI No
77 AUX_COM_CONFIG_TO_FLASH Writes Aux Comm configuration to flash All Controls OCI No
83 AUX_COM_DOWNLOAD_FILE Aux Comm download file All Controls OCI 2 No Local File Name STRING1 Remote File Name STRING1
151 AUX_COM_HOST_FROM_FLASH Aux Comm host address config read from flash All Controls OCI No
84 AUX_COM_HOST_WRITE_TO_FLASH Aux Comm host address config writes to flash All Controls OCI No
80 AUX_COM_SENDCMD Aux Comm send command All Controls OCI 1 No Command Index 1-64 DINT
70 COPY_DEVICE_SETUP_DEFAULTS Copies defaults for device setup All Controls OCI 2 No Device Num enum DINT Port ID enum DINT
89 DEACTIVATE_RIO_PASSTHROUGH Deactivates remote I/O passthrough All Controls OCI No
101 ENTER_SERIAL_IO_MONITOR_MODE Enters serial I/O monitoring mode All Controls OCI 2 No Port ID enum DINT Receive/Transmit DINT
102 EXIT_SERIAL_IO_MONITOR_MODE Exits serial I/O monitoring mode All Controls OCI No
156 INITIALIZE_DEVICE_SETUP Initialize the RAM copy of device setup at startĆ
up
All Controls OCI No
74 REPEAT_TX_SERIAL_IO Repeat transmits on serial I/O All Controls OCI 1 No Repeat Char DINT
112 SAVE_DEVICE_SETUP Saves changes to device setup All Controls OCI No
73 SINGLE_TX_SERIAL_IO Single transmits on serial I/O All Controls OCI 1 No Char DINT
71 START_SERIAL_IO_MONITOR Starts serial I/O monitor All Controls OCI No
72 STOP_SERIAL_IO_MONITOR Stops serial I/O monitor All Controls OCI No
Miscellaneous
63 CANCEL_MESSAGE Cancels active messages All Controls Both No
4 CALCULATE Perform a math calculation on a string All Controls Both 1 Yes Calc_string STRING1
86 CLEAR_ACTIVE_ERRORS Clears active errors All Controls Both Yes
109 CLEAR_CYCLE_TIME Clears cycle time All Controls Both Yes
59 CLEAR_DEBUG_MONITOR Clears fields in the debug monitor parameters All Controls Both 1 No Parameter Index
enum
DINT
87 CLEAR_ERROR_LOG Clears error log All Controls Both No