Rockwell Automation GV3000/SE, VTAC 7 Super Remote Meter Interface Board M/N 2SI3000 M/N 2SI3000E User Manual
Page 82
Index-2
Super Remote Meter Interface (RMI) Board
G
GV3000/SE drive
hardware, 1-1
software, 1-1
H
hardware (GV3000/SE and VTAC 7 drives), 1-1
I
inputs
analog, 2-3
digital, 2-2
frequency, 2-3
installation, 3-1
1 to 20 HP @ 230 VAC drives, 3-12
1 to 5 HP @ 460 VAC drives, 3-4
100 to 150 HP @ 460 VAC drives, 3-26
15 to 25 HP @ 460 VAC drives, 3-21
2 to 43 amp Bookshelf drives, 3-34
200 to 400 HP @ 460 VAC drives, 3-31
25 to 60 HP @ 460 VAC drives, 3-21
30 to 100 HP @ 230 VAC drives, 3-16
50 to 100 HP @ 460 VAC drives, 3-26
60 to 100 HP @ 460 VAC drives, 3-26
7.5 to 10 HP @ 460 VAC drives, 3-8
75 to 200 @ 460 VAC drives, 3-16
J
jumpers (RMI board)
factory default settings, 2-1
location, 2-1
L
LED, status indicator, 2-1
Low Speed Detection Level (r.056), 4-15
M
mechanical description, RMI board, 2-1
O
Outer Loop PI Regulator, programming, 4-4
outputs
analog, 2-3
digital, 2-2
relay, 2-3
P
parameters
descriptions, 4-1
menu structure, 4-1
r, 4-1 to 4-15
alphabetic list, B-1
recording settings, 4-1
second menu, 4-1
PI Regulator Integral Gain (r.022), 4-4
PI Regulator Offset (r.020), 4-4
PI regulator operating modes, 4-4
PI Regulator Proportional Gain (r.021), 4-4
power consumption, A-2
programming reference, 4-1
R
r parameters, 4-1 to 4-15
alphabetic list, B-1
Relay Output 1 (NO) Configuration (r.035), 4-10
Relay Output 1 Delay Time (r.044), 4-14
Relay Output 2 (NO/NC) Configuration (r.036), 4-10
Relay Output 2 Delay Time (r.045), 4-14
Relay Output 3 (NO/NC) Configuration (r.037), 4-10
Relay Output 3 Delay Time (r.046), 4-14
relay outputs, 2-3
configuration, 4-10
specifications, A-2
timers, programming, 4-14
RMI board, mechanical/electrical description, 2-1
S
second menu parameters, 4-1
software (GV3000/SE and VTAC 7 drives), 1-1
specifications, A-1
Speed Detection Hysteresis Band (r.053), 4-15
Speed Detection Level 1 (r.050), 4-15
Speed Detection Level 2 (r.051), 4-15
Speed Detection Level 3 (r.052), 4-15
speed reference source, 4-7, 4-9
status LED, 2-1
T
technical specifications, A-1
terminal strip
connections, 3-41
signals, 2-2
timers, programming digital and relay output, 4-14
Torque Detection Hysteresis (r.066), 4-15
Torque Detection Level 1 (r.063), 4-15
Torque Detection Level 2 (r.064), 4-15
Torque Detection Level 3 (r.065), 4-15
Torque or Current Limit Selection (r.025), 4-5, 4-6
Torque/Current Limit Source (r.025), 4-5
trim reference source, RMI board as, 4-15
troubleshooting, 5-1
V
VTAC 7 drive hardware/software, 1-1