Speaker distance c):5p disthhcie, Unit unît, Speaker distances – Yamaha HTR-5860 User Manual
Page 70: Center graphic equalizer [fjequf"!' ‘ i, Coeguplizer
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
SET MENU
■ Speaker distance C):5P DIST
h
HCIE
Use this feature to manually input the distance of each
speaker and adjust the delay applied to respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sound will arrive at the listening position at the same time.
Unit UNÎT
Choices: meters (m),
feet
(ft)
Initial setting: feet (ft)
• Select meters to input speaker distances in meters.
• Select feet to input speaker distances in feet.
Speaker distances
Choices; 0.3 to 24.00 m (1 to 80 ft)
• FRONT
Ladj lists the distance of the front left speaker.
Initial setting: 3.0 ni (10.0 ft)
• FRONT R
adjusts the distance of the front right
speaker. Initial setting: 3.0 in (10.0 ft)
• CENTER
adjusts the distance of the center speaker.
Initial setting: 3.0 m (10.0 ft)
• SUR. L
adjusts the distance of the surround left
speaker. Initial setting: 3.0 m (10.0 ft)
• SUR. R
adjusts the distance of the surround right
speaker. Initial setting: 3.0 m (10.0 ft)
• SB L*
adjusts the distance of the surround back left
speaker. Initial setting: 2.10 in (7.0 ft)
• SB R*
adj u,sts the distance of the surround back right
speaker. Initial setting: 2.10 m (7.0 ft)
• SWFR
adjusts the distance of the subwoofer. Initial
setting: 3.0 m (10.0 ft)
• PRESL
adjusts the distance of the presence left
speaker. Initial setting: 3.0 m (10.0 ft)
• PRES R
adjusts the distance of the presence right
speaker. Initial setting: 3.0 m (10.0 ft)
• Instead of SB L and SB R. SUR. B will be displayed if you
selected only one surround back speaker in SUR. B L/R SP
(page 64).
■ Center graphic equalizer [fJEQUf"!' ‘ i "
Use this feature to select the parametric (AUTO PEQ) or
graphic equalizer (CNTR GEQ).
Equalizer lEiJ TvF'E SlELJECiT
Select to change the type of equalizer u.sed by this unit.
Choices: AUTO PEQ,
CNTR GEQ,
EQ OFF
• Select AUTO PEQ to use the equalizer adjusted in auto
setup.
• Select CNTR GEQ to adjust the built-in 5-band graphic
equalizer so that the tonal quality of the center speaker
matches that of the front left and right speakers.
• Select EQ OFF to cancel equalizing.
Center graphic equalizer CiEhlTIEf? 6EQ
When CNTR GEQ is selected, use this feature to output a
test tone and adjust the tonal quality so that it matches that
of the front left speaker.
You can adjust 5 frequency bands:
lOOHz, 300Hz, 1 kHz, 3kHz, lOkHz
Choices: -6 to -1-6 dB
Initial setting: 0 dB
COEGUPLIZER
T'EST MDF'F OH
Select ON to output test tones from the front left and
center speakers, and adjust the tonal quality of the
center speaker.
Select OFF to .stop the test tone and output the
currently selected source component.
Press /\ / xz to select a frequency band.
Press <( / )> to adjust the selected frequency band.
66