KEYENCE SR-750 Series - Manual (Page 74)

74 E SR-750 UM
„ Forced trigger lock release
Send command UNLOCK
Response Normal process OK, UNLOCK
Abnormal process ER, UNLOCK, ee ee: Error code
• Releases trigger lock.
„ Obtaining forced trigger lock status
Send command RLOCK
Response
OK, RLOCK, nnnn
nnnn = forced trigger lock status
"LOCK" or "UNLOCK" is added.
Laser Pointer Control
The laser pointer for confirming a code position lights up or lights off using a
command.
„ Laser Pointer ON
Send command LDON
Response Normal process OK, LDON
Abnormal process ER, LDON, ee ee: Error code
„ Laser Pointer OFF
Send command LDOFF
Response Normal process OK, LDOFF
Abnormal process ER, LDOFF, ee ee: Error code
Tuning
„ Starting tuning
Send command TUNE, bb
Response
OK, TUNE
bb = 01 to 10: Reading bank number: 1 to 10
When tuning operation is complete, the result is output in the following formats.
Success : Tuning SUCCEEDED,Tms,00000x00
Failure : Tuning FAILED,Tms,00000x0y
Tms: Tuning time
x: Advice 0,1,2,4
0: No advice
1: Filter process change may be enabled.
2: Installation condition, lighting condition or marking
condition adjustments should be considered.
4: Brightness may be insufficient.
y: Failure factor 1,2 1: Code detection impossible
2: Unstable reading
• Tuning process starts.
• When tuning is successful, the result is saved to the specified bank (also saved
to the ROM).
„ Finishing tuning
Send command TQUIT
Response
OK, TQUIT
• Tuning process finishes.
„ Obtaining the alternate order
Send command BANKORDER
Response Normal process OK, BANKORDER, bb/bb/bb/· · ·
bb: parameter bank number (01 - 10)
Abnormal process ER, BANKORDER, ee ee: Error code
• The parameter bank numbers to alternate are returned in turn.
• The parameter bank numbers are returned with the number of parameter bank
numbers registered with the SR-750 Series. (max. 16)
• If there is no parameter bank number to alternate, an error is returned.
• If Specify response character is set to "SR-600 compatible", bb/bb/bb· · ·
is returned for normal process and ERRee is returned for abnormal process.
"3-9 SR-600 Compatible Output Mode (Page 19)"
„ Initializing the parameter bank
Send command BANKCLR, bb bb: parameter bank number (00 - 10)
00 = Initialize all parameter banks
01 - 10 = Initialize specified
parameter banks only
Response Normal process OK, BANKCLR
Abnormal process ER, BANKCLR, ee ee: Error code
• If Specify response character is set to "SR-600 compatible", OK is returned for
normal process and ERRee is returned for abnormal process.
"3-9 SR-600 Compatible Output Mode (Page 19)"
Other Commands
„ Save settings
Send command SAVE
Response Normal process OK, SAVE
Abnormal process ER, SAVE, ee ee: Error code
• The SAVE command is sent to save in the memory the setting contents sent to
the SR-750 Series.
• The command setting is applied after the response of the SAVE command is
sent.
„ Obtaining configuration command status
Send command CMDSTAT
Response
OK, CMDSTAT, nnnn
nnnn = none
: No operation
wait : Wait for the setting applied
update : Program updating
• Command to obtain configuration change status. This is used to check the
process status of a configuration command such as WN, WP, and WB.
• If Specify response character is set to "SR-600 compatible", nnnn is returned.
"3-9 SR-600 Compatible Output Mode (Page 19)"
„ Setting initialization
Send command DFLT
Response Normal process OK, DFLT
Abnormal process ER, DFLT, ee ee: Error code
• Resets the SR-750 Series to the default configuration.
• When the SR-600 compatible output mode is "Enabled", OK and ERRee are
returned for normal process and abnormal process respectively.
"3-9 SR-600 Compatible Output Mode (Page 19)"
When executing the script file - status confirmation
command
„ Obtaining the script processing time
Send command SCPTIME
Response
OK, SCPTIME, now=AAus, max=BBus, min=CCus
AA: Returns the most recent script processing time.
BB: Returns the maximum value of the processing time.
CC: Returns the minimum value of the processing time.
• Returns the processing time of script executed after power ON.
„ Script debug setting
Send command SCPDBG, n
Response
OK, SCPDBG
n=0: Script debug OFF
n=1: Script debug ON
• Sets whether to output debug from the script file to the command port or not.
• Setting the debug ON executes print(str) and outputs data.
„ Obtaining the script error results
Send command SCPERR
Response
OK, SCPERR, mmmmmmmmmmmmmmmmmmmmmmmmmmmmmm
mm… : Script error character string
• Returns the details of script error.