Document Outline

• Installing and Connecting the MDF and Telephones
• Contents
• Chapter 1: Introduction
  • Audience
  • How to use this documentation
    • Downloading this book and updates from the Web
    • Sending us comments
  • Related resources
• Chapter 2: Installing the main distribution frame
  • Physical requirements and layout
    • Installation space requirements
    • Installation layout
  • Main distribution frame cross-connect fields
  • Main distribution frame hardware installation
  • Main distribution frame placement
  • Main distribution frame labels
  • Mounting 110A- or 110P-type terminal blocks on the wall
  • Mounting 110P-type terminal blocks on a frame
  • Installing Cable Slack Managers
• Chapter 3: Installing the patch panel
  • Installing patch panels
  • Cross-connecting the media gateway to the patch panels
• Chapter 4: Media gateway connections to the MDF
  • Equipment room cabling labels
  • Cable routing guidelines
  • Trunk cables among network interface, sneak fuse panel, and media gateway
  • Installing cables between media gateway and MDF
  • Installing connector cables between auxiliary cabinet and MDF
• Chapter 5: MDF connections to stations and the public switched telephone network
  • Station (telephone) wiring design
  • Information outlets
  • Station cables
  • Closets
    • Satellite locations
    • Site locations
  • Station circuit distribution from equipment room
    • 4-pair station circuits
    • 3-pair to 4-pair station circuit distribution
  • Connected cable station adapters
  • Completing a provisioning plan
  • Installing sneak current and off premise protection
    • Installing sneak fuse panels
  • Installing the coupled bonding conductor
    • Installing coupled bonding conductor wires
  • Installing and administering the patch cord/jumper
    • Labeling expansion control carrier cable (MCC1 Media Gateway only)
    • Connecting expansion control carrier outputs cable (MCC1 Media Gateway only)
    • Connecting trunk pairs using concentrator cables
    • Connecting trunk pairs to media gateway using jumper wires to establish 3-pair modularity
• Chapter 6: Installing and wiring telephones and trunks
  • Wiring telephones and trunks
  • Connecting telephones
    • Connectable telephones and consoles
    • Connecting a typical telephone
    • Connecting adjunct power
    • Connecting an analog station or 2-wire digital station
    • Analog tie trunk example
    • Digital tie trunk example
    • DS1 tie trunk example
    • Collocated DS1 interface trunks
    • DS1 interface trunks using T1 channel service unit
  • Auxiliary connector outputs (MCC1 and SCC1 Media Gateways only)
  • Three-pair and four-pair modularity
  • Adjunct power connection locations
  • Attendant console example
    • Attendant console cabling distances, local and phantom power
    • Auxiliary power
    • Hard-wire bridging
    • Dual wiring of 2-wire and 4-wire endpoints
    • Installing the attendant console
    • Installing the 26B1 Selector Console
  • Connecting external alarm indicators and auxiliary power
  • Installing off-premises station wiring
  • Off-premises or out-of-building stations
  • Off-premises connections
    • Off-premises protection requirements
    • Telephone restrictions for exposed environments
    • Digital Out-of-Building Telephone Protection
      • Installing the ITW Linx Enhanced Protector
      • Installing the 4C3S-75 Enhanced Protector
      • Installing the data link protector
  • Emergency transfer units and associated telephones
  • 808A Emergency Transfer Panel and telephone installation examples
    • Installing the 808A Emergency Transfer Panel
    • Installing telephones used only for emergency transfer (trunk/auxiliary field)
    • Installing telephones used for emergency transfer and as normal extension (trunk/auxiliary field)
  • Installing external ringing
  • Installing the queue warning indicator
• Chapter 7: Installing and wiring telephone power supplies
  • 1145B2 power supply
    • Important warning for 1145B2 power supply
    • Mounting the 1145B2/1146B2 power supply
    • Installing the wall-mounting plates
    • Mounting the 1146B2 Power Distribution Unit
    • Installing the battery mounting/wiring
    • Installing the expanded power distribution unit
    • Powering up and testing the power supply
    • Wiring the 1146B2 Power Distribution Unit
    • Resetting LEDs on power distribution unit
  • 1152A1 Mid-Span Power Distribution Unit
    • Important safety instructions
    • Using the 1152A1 Power Distribution Unit
    • Connecting the 1152A1 Power Distribution Unit
    • Connecting the cables
      • Connecting cables to telephones and other end devices
  • 1152B Mid-Span Power Distribution Units
    • Important 1152B PDU Safety Instructions
    • Using the 1152B PDUs
    • Connecting the 1152B PDU cables
    • Connecting cables to telephones and other end devices
  • C360 converged stackable switches
    • C360 switch important safety instructions
    • Using the C360 switch
    • Connecting the C360 stackable switches
      • Connecting the cables
  • 1151B1 and 1151B2 Power Supplies
    • Important safety instructions for 1151B1 and 1151B2 Power Supplies
    • Using 1151B1 and 1151B2 Power Supplies
    • Connecting the 1151B1 or 1151B2 Power Supplies
• Chapter 8: Testing the complete configuration
  • Testing port network equipment
    • Checking port network status for each media gateway
    • Checking circuit pack configuration
    • Testing the TN2312BP Internet Protocol Server Interface circuit pack
    • Testing Expansion Interface circuit packs, if used
    • Testing time division multiplexing bus for each port network
    • Testing expansion interface exchange, if used, for each port network
  • Testing telephones and other equipment
    • Making test calls
    • Testing 302C attendant console
    • Testing selector console
    • Testing external ringing
    • Testing queue warning indicator
    • Testing integrated announcement
      • Record an announcement
      • Playback announcement
      • Delete announcement
    • Testing music-on-hold
    • Testing emergency transfer (Avaya S8700 Multi-Connect only)
    • Testing terminating trunk transmission
    • Testing connectivity to the LAN
  • LED indicators
    • Telephone console LEDs
      • Attendant console LEDs
      • Terminal alarm notification
    • DS1 Converter circuit pack LEDs
      • SPAN LEDs
• Index
  • Numerical
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • L
  • M
  • N
  • O
  • P
  • Q
  • R
  • S
  • T
  • U
  • V
  • W
  • Z