Projector user commands, Environment – Canon SX 50 User Manual
Page 30
Projector User Commands
- 24 -
Revision History / Date
Changes
Revised by
Approved by
Environment
This defines the environments that support the command (power supply state, input signal state).
Power
Input
Mode
Model
Parameter
OFF ON PM D-RGB A-RGB1 A-RGB2 COMP Video S-Video D-Video SCART None Remote Local
AUTO X O
X
X X X O
X X - - O O
X
NORMAL X O
X
O
O
O
O
O
O
- -
O O
X
WIDE X
O
X
X
O
O
O
O
O
- -
O
O
X
FULL X O
X
O
O
O
X X X - - O O
X
SX50
TRUE X O
X
O
O
O
X X X - -
X O
X
AUTO X O
X
O
O
O
O
X X O X O O
X
WIDE X O
X
O
O
O
O
O
O
O O O O
X
FULL X O
X
O
O
O
O
O
O
O O O O
X
SX6,
SX60,
X600
01.0100
TRUE X O
X
O
O
O
X X X X X X O
X
AUTO
X O
X
O
O
O
O
X X O X O O
X
WIDE
X O
X
O
O
O
O
O
O
O O O O
X
FULL
X O
X
O
O
O
O
O
O
O O O O
X
4:3
TRUE
X O
X
O
O
O
X X X X X X O
X
AUTO
X O
X
X X X X X X X X O O
X
WIDE
X O
X
O
O
O
O
O
O
O O O O
X
FULL
X O
X
X X X O
O
O
O O O O
X
16:9
TRUE
X O
X
X X X X X X X X X O
X
AUTO
X O
X
O
O
O
X X X X X O O
X
WIDE
X O
X
O
O
O
O
O
O
O O O O
X
FULL
X O
X
O
O
O
O
O
O
O O O O
X
SX6,
SX60,
X600
SX7,
X700,
01.0111
16:9
DIS
TRUE
X O
X
O
O
O
X X X X X X O
X
AUTO
X O
X
O
O
O
O
X X O X O O
O
WIDE
X O
X
O
O
O
O
O
O
O O O O
O
FULL
X O
X
O
O
O
O
O
O
O O O O
O
4:3
TRUE
X O
X
O
O
O
X X X X X X O
O
AUTO
X O
X
X X X X X X X X O O
O
WIDE
X O
X
O
O
O
O
O
O
O O O O
O
FULL
X O
X
X X X O
O
O
O O O O
O
16:9
TRUE
X O
X
X X X X X X X X X O
O
AUTO
X O
X
O
O
O
X X X X X O O
O
WIDE
X O
X
O
O
O
O
O
O
O O O O
O
FULL
X O
X
O
O
O
O
O
O
O O O O
O
SX7
Mark II
01.02**
16:9
DIS
TRUE
X O
X
O
O
O
X X X X X X O
O
* If a state is not supported, "INVALID_MODE", "NOT_POWER_SUPPLIED", “INVALID_SOURCE”,
“NOT_SUPPORTED_ASPECT” or “INVALID_SCREEN_ASPECT” is returned with the Err response.
* If the necessary signals are not input, 'INVALID_SIGNAL (*****)' or 'NO_SIGNAL' is returned.
* When the power supply state is in the process of switching, an "i:BUSY" reply may be sent.
* “4:3”, “19:9”, “16:9 DIS” represents the “Screen aspect ratio”.