Fostex D-160 - Manual (Page 177)

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)
177
Data Type
< l o o p o p . m o d e > < l o o p o p . m o d e > < l o o p o p . m o d e > < l o o p o p . m o d e > < l o o p o p . m o d e > 12=stop
Indicates the next operating mode following locating to the start point (GP1) upon
arriving at the end point (GP6) by the play mode.
In D-160, 12=stop only is effective.
< p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e > 12=stop
15=play
Specifies operating mode in which D-160 should enter upon completing the
locate operation. Corresponds to the setting of AUTO PLAY ON ("15")/OFF ("12") on
the main unit.
< c o u n t > < c o u n t > < c o u n t > < c o u n t > < c o u n t > 01~7F
Specifies succeeding data byte numbers.
< m m c t r a c k > < m m c t r a c k > < m m c t r a c k > < m m c t r a c k > < m m c t r a c k > Complies to the MMC (MIDI MACHINE CONTROL) standard track bit map.
In D-160, you always need to specify three byte combinations of "r0", "r1" and "r2."
< e d i t m e s s a g e > < e d i t m e s s a g e > < e d i t m e s s a g e > < e d i t m e s s a g e > < e d i t m e s s a g e > 00 = no message
01 = completed (completion flag)
02 = active (execution flag)
02<mmc time> = Indicates unprocessed time by active (execution flag) and <mmc
time>.
02<count><mmc track> = Indicates source track by active (execution flag) and
<mmc track>. Used for clipboard play.
03 = cancel (execution stop)
05 = Indicates rehearsal (rehearsal mode of auto rec). Possible of undo.
06 = Indicates take (take mode of auto rec). Possible of undo.
10 = over value error
10 <mmc time> = Capacity shortage time is indicated by over value error (error by
capacity shortage) and <mmc time>. In copy paste, it indicates capacity shortage
time required for a minimum one time paste.
11 = Indicates in point error (incorrect in point).
12 = Indicates out point error (incorrect out point).
14 = Indicates void data (data necessary for paste does not exist).
18 = Indicates track select error (track necessary to execute copy/move or erase/cut
is not correctly setup).
19<repeat count> = Indicates repeat number error and repeat numbers executable
by <repeat count>.
1A = Indicates disable rec (record disable mode).
71 = Indicates on.
72 = Indicates off.
< m m c t i m e > < m m c t i m e > < m m c t i m e > < m m c t i m e > < m m c t i m e > hr mn sc fr {ff/st} complies to the MMC standard time code.
< o n / o f f > < o n / o f f > < o n / o f f > < o n / o f f > < o n / o f f > 70 = default
71 = on
72 = off
< r e p e a t c o u n t > < r e p e a t c o u n t > < r e p e a t c o u n t > < r e p e a t c o u n t > < r e p e a t c o u n t > 01~7F
Especially when executing commands such as paste, the number of pasting times to
be continuously repeated following the auto punch in point is specified.
< c h a n n e l > < c h a n n e l > < c h a n n e l > < c h a n n e l > < c h a n n e l > 1~18, 7F
Select recorder tracks 1~18. "00" in particular, is not specified (default setting). "7F"
indicates input/output of Adat optical. For details, refer to explanation on setting
the Command/Mode.
< l o c k e n a b l e > < l o c k e n a b l e > < l o c k e n a b l e > < l o c k e n a b l e > < l o c k e n a b l e > 00 = lock disable, chase disable
01 = lock enable, chase enable
Corresponds to SLAVE ON ("01")/OFF ("00") in the main unit.
< l o c k s t a t u s > < l o c k s t a t u s > < l o c k s t a t u s > < l o c k s t a t u s > < l o c k s t a t u s > 00 = lock disable, chase disable
01 = lock enable (unlocked), chase enable (unlocked)
11 = lock enable (locked), chase enable (locked)
< p r o g r a m > < p r o g r a m > < p r o g r a m > < p r o g r a m > < p r o g r a m > 01~63H
Indicates program numbers (P1~P99) on the main unit. However, D-160 can specify
only 01 (corresponds to P1)~63H (corresponds to P99).
< l o c k m o d e > < l o c k m o d e > < l o c k m o d e > < l o c k m o d e > < l o c k m o d e > 40 = Free
42 = Vari
45 = SP DIF
46 = adat
Indicates the slave mode when this equipment is set to slave ON.