Rockwell Automation SP500 AC Drive Installation and Operation Manual - Manual (Page 9)

Contents III
List of Figures
Figure 2.1 – SP500 System Diagram ....................................................................... 2-3
Figure 2.2 – SP500 System Diagram (Continued) ................................................... 2-4
Figure 2.3 – Regulator Board Component Locations ............................................... 2-5
Figure 2.4 – Identifying the Drive Model Number ..................................................... 2-6
Figure 2.5 – Enclosure A Component Locations ...................................................... 2-9
Figure 2.6 – Enclosure B Component Locations .................................................... 2-10
Figure 2.7 – Enclosure C Component Locations .................................................... 2-11
Figure 2.8 – Enclosure D Component Locations .................................................... 2-12
Figure 3.1 – Enclosure A Dimensions ...................................................................... 3-2
Figure 3.2 – Enclosure B Dimensions ...................................................................... 3-2
Figure 3.3 – Enclosure C Dimensions ...................................................................... 3-3
Figure 3.4 – Enclosure D Dimensions ...................................................................... 3-3
Figure 3.5 – How to Measure Motor Lead Lengths .................................................. 3-6
Figure 4.1 – Enclosure A Wire Routing Locations .................................................... 4-2
Figure 4.2 – Enclosure B Wire Routing Locations .................................................... 4-3
Figure 4.3 – Enclosure C Wire Routing Locations.................................................... 4-4
Figure 4.4 – Enclosure D Wire Routing Locations.................................................... 4-5
Figure 4.5 – Jumper J6 Settings for the Analog Input Speed Reference ................. 4-8
Figure 5.1 – Typical Electrical Connections.............................................................. 5-2
Figure 5.2 – Typical Control Terminal Strip Connections ......................................... 5-3
Figure 5.3 – Analog Speed Reference Wiring Connections ..................................... 5-4
Figure 5.4 – Analog Output Wiring Connections ...................................................... 5-4
Figure 5.5 – Two-Wire Start/Stop Sample Control Wiring ........................................ 5-5
Figure 5.6 – Three-Wire Start/Stop Sample Control Wiring..................................... 5-5
Figure 5.7 – Multi-Speed Preset Sample Control Wiring .......................................... 5-6
Figure 5.8 – Terminal Usage During Multi-Speed Preset Operation ........................ 5-7
Figure 5.9 – Snubber Resistor Wiring Connections for M/N 1SU2xxxx Drives ........ 5-9
Figure 5.10 – Snubber Resistor Wiring Connections for M/N 1SU4xxxx and
1SU5xxxx Drives ................................................................................ 5-9
Figure 5.11 – Output Status Relay Wiring Connections ......................................... 5-10
Figure 7.1 – SP500 Keypad and Display.................................................................. 7-1
Figure 7.2 – SP500 Menu Structure ......................................................................... 7-4
Figure 7.3 – Example of a Program Mode Display .................................................. 7-5
Figure 7.4 – Example of a Monitor Mode Display..................................................... 7-6
Figure 8.1 – Manual Torque Boost Adjustment Range............................................. 8-7
Figure 8.2 – Volts/Hertz Curve ................................................................................. 8-8
Figure 9.1 – DC Bus Terminals on Model 1SU1xxxx and 1SU2xxxx Drives ............ 9-2
Figure 9.2 – DC Bus Terminals on Model 1SU4xxxx and 1SU5xxxx Drives (except
1SU4x015, 1SU4x020)......................................................................... 9-2
Figure 9.3 – DC Bus Terminals on Model 1SU4x015 and 1SU4x020 Drives........... 9-2