Teac HS-4000 - Manual (Page 99)

TASCAM HS-4000
99
10 – On-air mode
Examples of playback areas when the ON AIR button
is ON, Follow BWF-J is ON and the BC$ END mode is
Jump to Standby
BC$STANDBY BC$END
BC$STANDBY BC$END
BC$STANDBY
1st Take
2nd Take
3rd Take
4th Take
Played area
Played area
Played area
Played area
The next take has a BC$STANDBY
mark, so playback goes up to the
BC$END mark.
The next take has a BC$STANDBY
mark, so playback goes up to the
BC$END mark.
The next take has no BC$STANDBY
mark, so playback goes to the end of
the Take.
There is no next take, so playback
goes to the end of the Take.
Using the ON AIR button to switch
between rehearsal/confirmation
playback and actual playback modes
On the Home Screen or ON AIR LIST screen, press the ON AIR
button to switch between rehearsal/confirmation playback and
actual play modes.
ON AIR button ON (red): actual playback mode
The CREDITS 7 button is disabled, and only the on-air
mode playback area can be played back. (See “Playback
areas in on-air mode” on page 98.).)
The CREDITS 7, ON AIR LIST screen check and file name
buttons are disabled.
When you switch from OFF to ON, the transport jumps to
the beginning of the first take and enters playback standby.
ON AIR button OFF: rehearsal/confirmation playback
mode
The CREDITS 7 button is enabled, and locating to and
playing back any part of a take is possible.
When you switch from ON to OFF, playback stops at the
current position.
NOTE
The ON AIR button only function when playback is stopped
or in standby.
On-air playback
Press the PLAY key to start playback.
Press the PAUSE key to enter playback standby.
To end playback standby, press the PLAY key.
Press the STOP (RETAKE) key to stop playback.
Use the. [MARK.] and / [MARK /] keys to switch
entries.
Press and hold the m [
] key or , [ ] key to
search backward or forward.
Press the. [MARK.] or / [MARK /] key while pressing
and holding the SHIFT key to move between marks.
Press and hold the m[
] or ,[ ] key while pressing
and holding the SHIFT key to search at high-speed.
NOTE
• On the PLAY SETUP screen, you can set whether only the
currently selected entry is played or whether all the entries
within the current playlist are played. In addition, you can
also turn repeat playback on and off (in single and dual
modes). (See “Online function” on page 35.)
• Playback can also be controlled via the PARALLEL
connector.
Conducting credits playback
1. On the Home Screen or ON AIR LIST screen, press the ON AIR
button to turn it off.
2. Use the file name selection buttons on the ON AIR LIST
screen or the.//keys to select the current take.
NOTE
• Only files that are valid for on-air playback can be selected
as the current take.
• When you turn the unit on, switch the sampling frequency
or switch to on-air mode, the first file in the list of files
available for on-air playback is selected as the current take.
3. On the Home Screen or ON AIR LIST screen, touch the
CREDITS 7 button to start credits playback from the
beginning of the current take and stop at the appropriate
mark.
• When the Follow BWF-J setting is ON, playback is from
the beginning of the file to the first BC$STANDBY mark.
• When the Follow BWF-J setting is OFF, playback is from
the beginning of the file to the first mark.
• If a selected file does not have a valid mark, playback will
continue until the end of the file and then stop.
During playback, the take name button on the ON AIR LIST
screen will become green.
4. During credits playback, touch the CREDITS 7 button to
stop.
NOTE
The file name selection and CREDITS 7 buttons on the ON
AIR LIST screen can be used when playback is stopped and
the ON AIR button is off and during credits playback when
the ON AIR button is off.
They are disabled when the ON AIR button is ON and during
ordinary playback.
Using the call function
Press the CALL (CHASE) key to locate to the point where
playback was last started from playback standby (call point) and
put the unit in playback standby mode.