SATO HT200e - Manual (Page 41)

SECTION 2: INSTALLATION AND SETUP
SATO HT200e Page 2-23
PROCESS ON THE SCREEN FOR TRANSFER OF PRINT PARAMETER
6 + Power “ON”
[ ← ] [ → ]
Or:
Or:
Print parameter that is transferred from a host computer will be registered in a printer. The parameter
registered in the printer can be transferred to the host.
Note: When print parameter is transferred, on-line cable must be connected to the host before turning the power
“ON”.
P A R Ａ Ｍ Ｅ Ｔ Ｅ Ｒ Ｃ Ｏ Ｐ Ｙ
1 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｃ Ａ Ｒ Ｄ
Ｄ Ａ Ｔ Ａ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
2 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｄ Ａ Ｔ Ａ Ｓ Ｅ Ｎ Ｄ ／ Ｒ Ｅ Ｃ
3 Ｈ Ｔ → Ｈ Ｏ Ｓ Ｔ Ｈ Ｏ Ｓ Ｔ → Ｈ Ｔ
Ｈ Ｔ → Ｈ Ｏ Ｓ Ｔ Ｓ Ｅ Ｎ Ｄ Ｏ Ｋ ？
Ｙ ／ Ｎ
Ｈ Ｏ Ｓ Ｔ → Ｈ Ｔ Ｒ Ｅ Ｃ Ｏ Ｋ ？
Ｙ ／ Ｎ
Ｓ Ｅ Ｎ Ｄ Ｉ Ｎ Ｇ
Ｉ Ｔ Ｅ Ｍ : ０ ０ ０ １
Ｒ Ｅ Ｃ Ｅ Ｉ Ｖ Ｉ Ｎ Ｇ
Ｉ Ｔ Ｅ Ｍ : ０ ０ ０ １
Press [ENTR], so that it goes to the screen for
the selection of copying print parameter.
Press [
→ ], so that it goes to the process No. 2.
Press [ENTR], so that it goes to the screen for the
selection of transferring print parameter.
Press [
← ], so that it returns to the process No. 1.
Press [ENTR], so that it goes to the screen for the
selection of transferring print parameter.
Press [ENTR]:
“Y” is to start transfering.
“N” is to return to the process No. 2.
Press [ENTR]:
“Y” is ready for receiving.
“N” is to return to the process No. 2.
IMPORTANT: When “Y” is selected and [ENTR] is
pressed, all formats registered will be gone cleared
When receiving one item is complete, the number
of items will be added.
After receiving, it returns to the process No. 2.
When sending one item is complete, the number of
items will be added.
After sending, it returns to the process No. 2.