SATO HT200e User Manual
Page 49
SECTION 2: INSTALLATION AND SETUP
SATO HT200e
Page 2-31
PROCESS ON THE SCREEN FOR VOLTAGE INDICATION OF BATTERY
9 + Power “ON”
[
← ]
[
→ ]
[PGUP]
[ENTR]
Note: For Service Maintenance Mode, FULL/EMPTY can not be made available for the voltage indication of
battery. The battery voltage can only be displayed. Whether the battery is FULL or EMPTY will become
available when power is applied.
PROCESS ON THE SCREEN FOR VOLTAGE INDICATION OF RAM BACK-UP
MEMORY
9 + Power “ON”
[
← ]
[
→ ]
[
← ]
[
→ ]
[PGUP]
[ENTR]
Note: For Service Maintenance Mode, FULL/EMPTY can be made available for the voltage indication of RAM’s
back-up memory. The voltage can be not displayed. Whether the voltage is FULL or EMPTY will become
available for the back-up memory when power is applied.
Ｔ Ｅ Ｓ Ｔ
Ｐ Ｒ Ｉ Ｎ Ｔ
1
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
Ｃ Ｈ Ｅ Ｃ Ｋ
2
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
Ｃ Ｈ Ｅ Ｃ Ｋ
８ ． ６ Ｖ
Ｔ Ｅ Ｓ Ｔ
Ｐ Ｒ Ｉ Ｎ Ｔ
1
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
Ｃ Ｈ Ｅ Ｃ Ｋ
2
Ｒ Ａ Ｍ
Ｂ Ａ Ｃ Ｋ
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
3
Ｒ Ａ Ｍ
Ｂ Ａ Ｃ Ｋ
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
Ｆ Ｕ Ｌ Ｌ
Press [ENTR], so that it starts test print.
Press [
→ ], so that it goes to the process No. 2.
Press [ENTR], so that it displays voltage in battery.
Press [
← ], so that it returns to the process No. 1.
Press [PGUP], so that it returns to the screen for the
selection of voltage indication in battery.
Press [ENTR], so that it starts test print.
Press [
→ ], so that it goes to the process No. 2.
Press [ENTR], so that it displays voltage in battery.
Press [
← ], so that it returns to the process No. 1.
Press [
→ ], so that it goes to the process No. 3.
Press [ENTR], so that battery level (or remaining
fuel) can be indicated for RAM’s back-up.
Press [
← ], so that it returns to the process No. 2.
Press [PGUP], so that it returns to the screen for the
selection of battery level indication for RAM’s back-
up.