SATO HT200e - Manual (Page 47)

SECTION 2: INSTALLATION AND SETUP
SATO HT200e Page 2-29
PROCESS ON THE SCREEN FOR EAN COUNTRY CODE SETTING
6 + Power “ON”
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
Note: When EAN COUNTRY CODE is entered, or when either AC is pressed without no numeric entry or [ ← ] or
[ → ] is used after entering value in 1 digit (or less than 2 digits), DEFAULT will return to 50.
Ｐ Ａ Ｒ Ａ Ｍ Ｅ Ｔ Ｅ Ｒ Ｃ Ｏ Ｐ Ｙ
1 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｃ Ａ Ｒ Ｄ
Ｄ Ａ Ｔ Ａ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
2 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｓ Ｔ Ｒ ／ Ｒ Ｃ Ａ Ｌ Ｌ
3 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｆ Ｏ Ｎ Ｔ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
4 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｔ Ａ Ｂ Ｌ Ｅ Ｓ Ｔ Ｒ ／ Ｒ Ｃ Ａ Ｌ Ｌ
5 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｃ Ｕ Ｒ Ｒ Ｅ Ｎ Ｃ Ｙ Ｓ Ｅ Ｌ Ｅ Ｃ Ｔ
6
Ｃ Ａ Ｒ Ｄ Ｃ Ｌ Ｅ Ａ Ｒ
7
Ｅ Ａ Ｎ Ｃ Ｏ Ｕ Ｎ Ｔ Ｒ Ｙ Ｃ Ｏ Ｄ Ｅ
8 ５ ０
Press [ENTR], so that it goes to the screen for the
selection of transferring print parameter.
Press [
← ], so that it returns to the process No. 1.
Press [ → ], so that it goes to the process No. 3.
Press [ENTR], so that it goes to the screen for the
selection of copying print parameter.
Press [
→ ], so that it goes to the process No. 2.
Press [ENTR], so that it goes to the screen for the
selection of transfering preset.
Press [
← ], so that it returns to the process No. 2.
Press [ → ], so that it goes to the process No. 4.
Press [ENTR], so that it goes to the screen for the
selection of transfering font.
Press [
← ], so that it returns to the process No. 3.
Press [ → ], so that it goes to the process No. 5.
Press [ENTR], so that it goes to the screen for the
selection of transfering table data.
Press [
← ], so that it returns to the process No. 4.
Press [ → ], so that it goes to the process No. 6.
Press [ENTR], so that it goes to the screen for the
selection of currency mark.
Press [
← ], so that it returns to the process No. 5.
Press [ → ], so that it goes to the process No. 7.
Press [ENTR], so that it goes to the screen for the
selection of the card clear type.
Press [
← ], so that it returns to the process No. 6.
Press [ → ], so that it goes to the process No. 8.
[0] to [9] can be set in 2 digits, so that it permits the
entry ranging from 00 to 99.
Press [
← ] , so that it returns to the process No. 7.