SATO HT200e - Manual (Page 48)

SECTION 2: INSTALLATION AND SETUP
Page 2-30 SATO HT200e
PROCESS ON THE SCREEN FOR SERVICE MAINTENANCE MODE
9 + Power “ON”
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
Press [ENTR], so that it can go to each screen for processing.
For Service Maintenance Mode, [PGUP] is invalid, whereas [FMT] is valid.
PROCESS ON THE SCREEN FOR TEST PRINT
9 + Power “ON”
[ENTR]
[ENTR]
[ENTR]
Ｔ Ｅ Ｓ Ｔ Ｐ Ｒ Ｉ Ｎ Ｔ
1
Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ Ｃ Ｈ Ｅ Ｃ Ｋ
2
Ｒ Ａ Ｍ Ｂ Ａ Ｃ Ｋ Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
3
Ｃ Ａ Ｒ Ｄ Ｂ Ａ Ｔ Ｔ Ｅ Ｒ Ｙ
4
Ｒ Ｏ Ｍ Ｖ ｅ ｒ ．
5 １ Ｗ ０ ０ ０ ０
Ｔ Ｅ Ｓ Ｔ Ｐ Ｒ Ｉ Ｎ Ｔ
1
Ｌ Ａ Ｂ Ｅ Ｌ Ｔ Ｙ Ｐ Ｅ
Ｎ Ｏ Ｒ Ｍ Ａ Ｌ Ｏ Ｐ Ｔ Ｉ Ｏ Ｎ
Ｌ Ａ Ｂ Ｅ Ｌ Ｓ Ｉ Ｚ Ｅ
Ｐ ［ １ ０ ３ ］ Ｗ ［ ４ ８ ］ ｍ ｍ
Ｔ Ｅ Ｓ Ｔ Ｐ Ｒ Ｉ Ｎ Ｔ Ｉ Ｎ Ｇ
Press [ENTR], so that it displays voltage in battery.
Press [
← ], so that it returns to the process No. 1.
Press [ → ], so that it goes to the process No. 3.
Press [ENTR], so that it starts test print.
Press [
→ ], so that it goes to the process No. 2.
Press [ENTR], so that battery level (or remaining
fuel) can be indicated for RAM’s back-up.
Press [
← ], so that it returns to the process No. 2.
Press [ → ], so that it goes to the process No. 4.
Press [ENTR], so that battery level (or remaining
fuel) can be indicated for card’s back-up.
Press [
← ], so that it returns to the process No. 3.
Press [ → ], so that it goes to the process No. 5.
A ROM version can be displayed:
Note that [ENTR] is not available.
Press [
← ], so that it returns to the process No. 4.
Select label type with [ ← ] and [ → ] and press
[ENTR],so that it goes to the screen for label size.
Press [ENTR], so that it goes to the screen for the
selection of the label type in the test print.
Label size can be entered with numeric keypad:
Press [ENTR], so that it starts printing.
Test print will be terminated when printing one sheet
of paper is complete: Press [S/S], so that test print
can be executed as is ordered.
Ensure that whether label has been properly set prior
to test print.