Burkert Type 8056 - Manual (Page 60)

- 60 - RS232_485_ETP_MODBUS_BU_REV02.doc
CFLST (Configuration LiST) Read command: CFLST? The list command if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
COMMANDS AND FUNCTIONS SPECIFIC TO GPRS COMMUNICATION
Name and description Modes Returned values or codes
Read command: GPAPN?
String value if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Set command:
GPAPN=
string
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if string out of range
5:ACCESS ERR if insufficient access level
GPAPN (GPrs Access Point Name)
Reads or sets the GPRS network
access point name. This parameter
must be set accordingly to what is
specified by the wireless operator
and it is a string of max. 31
characters length.
Help command: GPAPN=?
MAX 31 CHR STRING if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: GPUSR?
String value if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Set command:
GPUSR=
string
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if
string out of range
5:ACCESS ERR if insufficient access level
GPUSR (GPrs USeR) Reads or sets
the GPRS network access user name.
This parameter must be set
accordingly to what is specified by
the wireless operator and it is a
string of max. 15 characters length.
Help command: GPUSR=? MAX 15 CHR STRING if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: NOT
SUPPORTED
1:CMD ERR if command issued
5:ACCESS ERR if insufficient access level
Set command:
GPPSW=
string
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if string out of range
5:ACCESS ERR if insufficient access level
GPPSW (GPrs PaSsWord) Sets the
GPRS network access password. This
parameter must be set accordingly to
what is specified by the wireless
operator and it is a string of max. 7
characters length.
Help command: GPPSW=? MAX 7 CHR STRING if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: GPEMF? String value if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Set command:
GPEMF=
string
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if
string out of range
5:ACCESS ERR if insufficient access level
GPEMF (GPrs EMail From) Reads or
sets the GPRS network email sender
address. This parameter must be set
to an existing mail address. The
maximum length is 31 characters.
Address of sender : this address
will be used in case of the mail
server cannot deliver the
message to the final destination.
In this case the message will be
bounced to the sender, so it is
possible to detect the error.
Help command: GPEMF=?
MAX 31 CHR STRING if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: GPEMT?
String value if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level GPEMT (GPrs EMail To) Reads or
sets the GPRS network email receiver
address. This parameter must be set
to an existing mail address. The
maximum length is 31 characters.
Address where the converter
send the e-mail ( data )
Set command:
GPEMT=
string
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if string out of range
5:ACCESS ERR if insufficient access level