Yokogawa FVX110 - Manual (Page 76)

<12. Parameter Lists>
12-3
IM 01S01C01-01EN
Relative
Index Index
Parameter Name Factory Default Write
Mode
Explanation
54 1054 SOFTDWN_FORMAT 0x01 AUTO Selects the software download method.
0x01: Standard
0x02: YOKOGAWA Standard
55 1055 SOFTDWN_COUNT 0 — Indicates the number of times the internal FlashROM was
erased.
56 1056 SOFTDWN_ACT_
AREA
0 — Indicates the ROM number of the currently working FlashROM.
0: FlashROM #0 working
1: FlashROM #1 working
57 1057 SOFTDWN_MOD_
REV
1, 0, 0, 0, 0, 0,
0, 0, 0
— Indicates the software module revision.
58 1058 SOFTDWN_ERROR 0 — Indicates the error during a software download.
Refer Table A8.4.
59 1059 SOFTDWN_HISTORY — Not used by the FVX110.
60 1060 SOFTDWN_HIST_INDEX 0 AUTO Not used by the FVX110.
61 1061 COMPATIBILITY_REV 1 — Indicates the smallest Rev value compatible with device
DevRev.
62 1062 CAPABILITY_LEV 0x00 — Indicates the capability level of instrument interior.
63 1063 CAPABILITY_CONFIG 0x0000 — A parameter corresponding to AP_CONF or DEV_OPTIONS
before the addition of parameter CAPABILITY_LEV.
64 1064 WRITE_LOCK_LEVEL 2 AUTO Specifies blocks that activates Write Lock.
65 1065 SI_CONTROL_CODES 1 — A parameter for switching to make the instrument compatible
with SI units.
66 1066 FD_VER 0 — Indicates value of major version of instrument diagnostics
specifications (FF-912).
67 1067 FD_FAIL_ACTIVE 0 — A parameter that corresponds to ”Failed” in the NAMUR NE-
107 category.
68 1068 FD_OFFSPEC_ACTIVE 0 — A parameter that corresponds to ”Off Specification” in the
NAMUR NE-107 category.
69 1069 FD_MAINT_ACTIVE 0 — A parameter that corresponds to ”Maintenance” in the NAMUR
NE-107 category.
70 1070 FD_CHECK_ACTIVE 0 — A parameter that corresponds to ”Check Function” in the
NAMUR NE-107 category.
71 1071 FD_FAIL_MAP 0xFC000000 AUTO Specifies the bit assigned to FD_FAIL_ACTIVE, a parameter
for indicating ”Failed,” a 32-bit alarm listed in FD_SIMULATE.
DiagnosticValue.
72 1072 FD_OFFSPEC_MAP 0x00003800 AUTO Specifies the bit assigned to FD_OFFSPEC_ACTIVE, a
parameter for indicating ”Off Specification,” a 32-bit alarm listed
in FD_SIMULATE. DiagnosticValue.
73 1073 FD_MAINT_MAP 0x000003E0 AUTO Specifies the bit assigned to FD_MAINT_ACTIVE, a parameter
for indicating ”Maintenance,” a 32-bit alarm listed in FD_
SIMULATE. DiagnosticValue.
74 1074 FD_CHECK_MAP 0x01FF8008 AUTO Specifies the bit assigned to FD_CHECK_ACTIVE, a
parameter for indicating ”Check Function,” a 32-bit alarm listed
in FD_SIMULATE. DiagnosticValue.
75 1075 FD_FAIL_MASK 0xFFFFFFFF AUTO Specifies the bit that notifies the host of 32-bit ”Failed” alarms
listed in FD_FAIL_ACTIVE.
76 1076 FD_OFFSPEC_MASK 0xFFFFFFFF AUTO Specifies the bit that notifies the host of 32-bit ”Off
Specification” alarms listed in FD_OFFSPEC_ACTIVE.
77 1077 FD_MAINT_MASK 0xFFFFFFFF AUTO A parameter that specifies the bit that notifies the host of
32-bit ”Maintenance” alarms listed in FD_MAINT_ACTIVE. A
parameter set by the user.
78 1078 FD_CHECK_MASK 0xFFFFFFFF AUTO Specifies the bit that notifies the host of 32-bit ”Check Function”
alarms listed in FD_CHECK_ACTIVE.
79 1079 FD_FAIL_ALM AUTO Indicates alarm information for alarms categorized under
”Failed.”
80 1080 FD_OFFSPEC_ALM AUTO Indicates alarm information for alarms categorized under ”Off
Specification.”
81 1081 FD_MAINT_ALM AUTO Indicates alarm information for alarms categorized under
”Maintenance”.
82 1082 FD_CHECK_ALM AUTO Indicates alarm information for alarms categorized under
”Check Function”.
83 1083 FD_FAIL_PRI 0 AUTO Indicates the FD_FAIL_ALM priority for an alarm.
84 1084 FD_OFFSPEC_PRI 0 AUTO Indicates the FD_OFFSPEC_ALM priority for an alarm.
85 1085 FD_MAINT_PRI 0 AUTO Indicates theFD_MAINT_ALM priority for an alarm.