Tweco 400 Ultra-Cut(March 2013) - Manual (Page 152)

APPENDIX A-12 Manual 0-5163
ULTRA-CUT 400
5 The following features are available in Ultracut CCM revision level BA and higher or S/N
05517201 and higher.
5 OK to Move2 – Provides a second set of N.O. contacts that close when arc transfer is detected. Contacts are rated
for maximum of 24 VAC/DC @ 1A. Simplified CNC Circuit.
5 +10V @ 10ma. For Remote CC Pot – Previously CCM versions if one wanted to use a potentiometer for the Remote
Analog Current Control (CC) input an external 10 V supply was required for Pot High.. Now an isolated (from main
plasma circuits) 10V supply is provided. Recommended value of the pot is 5K or 10K.
Ext. +10V
11
10
9
TB1
+10V
WIPER
Art # A-09246
5 Plasma Marking Select (Remote) – Plasma Marking, available only with DFC 3000, may be activated with a con-
tact closure between TB3-1 & TB3-2 if SW8-4, DIP switch on the CPU board (smaller of the 2 CCM boards), is also
on. Opening the connection between TB3-1 & TB3-2 switched back to normal cutting mode. For Ultracut power
supplies It is OK to leave SW8-4 on whether you are marking or not.
Simplified CNC Circuit.
Art # A-09191
I1
I1
I1
I1
OK2
OK2
Plasma Marking Remote
SW or Relay activated.
(use with DFC 3000 only)
Remote CC Pot connections
Remote Analog Current Control (+) J15 CNC
14 pin CPC
rear panel
Remote Analog Current Control (-)
Divided Arc V (-)
Divided Arc V (+)
SC 11 Comm Ref
START / STOP (+)
START / STOP (-)
ARC V_100K (+)
ARC V_100K (-)
OK to MOVE (-)
OK to MOVE (+)
Active LOW Logic Input
Active LOW Logic Input
All I-O except Plasma Marking is isolated
from plasma power supply circuits. TB3 is
not isolated. Activate with relay or switch
isolated from other circuits.
MOMENTARY START / STOP
START / STOP
TB1-4
TB1-5
TB1-6
SUSTAINED START / STOP
STOP
START
TB1-5
TB1-6
ALL SW OFF for 50:1 (default)
SW12-1 ON = 16.7:1 (SC-11)
SW12-2 ON = 30:1
SW12-3 ON = 40:1
SW12-4 ON = 25:1
ARC V (-)
Active LOW Logic Input
+16 to 18 VDC
(isolated)
OK to Move
PSR
ARC V (+)
Active LOW Logic Input
Active LOW Logic Input
+10 VDC @ 10ma. Supply for remote CC pot, +10 VDC @ 10ma.
Input Circuit
Common
(isolated)
OK to MOVE (+)
PREFLOW ON (+)
STOP (NC)
START/STOP Ret (-)
START/STOP OR START LATCH (+)
OK TO MOVE
output
(contacts or
DC Volts)
PILOT ON
output
(Contacts)
OK2- Suplemental
low voltage (24V)
OK to Move
Remote Analog Current Control input (+)
E-STOP input (+)
E-STOP Ret (-)
Remote Analog Current Control ret (-)
HOLD START (+)
DIVIDED ARC V (+)
DIVIDED ARC V (-)
HOLD START (-)
OK to MOVE (-)
PREFLOW ON (-)
To CPU PCB
Analog Input
Active LOW Logic Input
(not isolated)
CCM Module
+
-
+
-
1
8
7
6
2
1K 1K
TB3 TB3
1
2
SW12-3SW12-3
3
6
SW12-1SW12-1
1
8
1K 1K
1K 1K
SW11 SW11
2
1
3
J15 J15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SW12-4SW12-4
4
5
TB1 TB1
1
2
3
4
5
6
7
8
9
10
11
12
J4 J4
1
2
3
4
5
6
7
POT POT
.
.
.
TB1 TB1
9
10
11
J1 J1
1
2
3
4
5
6
7
8
9
SW12-2SW12-2
2
7
SW6 SW6
2
1
3
5
4
6
TB2 TB2
1
2
3
4
5
6
7
8
9
10
11
12