Marantz AV8801 - Manual (Page 116)

113
Playback
1
Press ZONE SELECT to switch
“ZONE2”, “ZONE3” or
“ZONE4”.
Input source
select buttons
2
Press ON/STANDBY X to turn on
the ZONE2, ZONE3 or ZONE4
power.
• Also press input source select button when
in standby mode, the power turns on.
• When ON/STANDBY X is pressed, ZONE2,
ZONE3 or ZONE4 turns off.
• Power in ZONE2, ZONE3 or ZONE4 can
be turned on or off by pressing ZONE2 ON/
OFF , ZONE3 ON/OFF or ZONE4 ON/OFF on
the main unit.
3 Press the input source select button to select the input
source to be played.
The audio and video signal of the selected source is output to
ZONE2, ZONE3 or ZONE4.
• Turn INPUT SELECTOR after pressing ZONE SELECT on the main
unit to select an input source.
When power for both MAIN ZONE and ZONE2 (ZONE3 or ZONE4) is
set to ON, power of the MAIN ZONE only can be turned off. Select
MAIN ZONE in step 1 then press
ON/STANDBY X .
Adjusting the volume
Use VOLUME df to adjust the volume.
GAdjustable rangeH 0 – 40 – 98
(When the “Scale” ( vpage 123 ) setting is “0 – 98”)
GAdjustable rangeH – – – –79dB – –40dB – 18dB
(When the “Scale” ( vpage 123 ) setting is “–79.5dB – 18.0dB”)
• At time of purchase, “Volume Limit” ( vpage 146 ) is set to “70
(–10dB)”.
Turn VOLUME after pressing ZONE SELECT on the main unit to adjust
the sound volume.
NOTE
For ZONE4, you cannot use VOLUME df to adjust the volume level.
Turning off the sound temporarily
Press MUTE : .
The sound is reduced to the level set at “Mute Level” ( vpage 146 )
in the menu.
• To cancel, either adjust the volume or press
MUTE : again.
• The setting can also be cancelled by adjusting the volume or turning
off the ZONE2 or ZONE3 power.
• You can adjust the tone and volume for ZONE2 or ZONE3 in “ZONE2
Setup” or “ZONE3 Setup” ( vpage 146 ) in the menu.
• The All Zone Stereo function allows you to simultaneously enjoy in
multi-zones (ZONE2/ZONE3) the music that is played back in MAIN
ZONE during home party, etc. (
vpage 82 “All Zone Stereo
function”).
Sleep timer function
• This is convenient for viewing and listening while going to sleep in
ZONE2, ZONE3 or ZONE4.
• The sleep timer function can be set by zone.
1
Press ZONE SELECT to switch
“ZONE2”, “ZONE3” or
“ZONE4”.
2
Press SLEEP and display the time
you want to set.
• The time switches as shown below each time SLEEP is pressed.
Off 10 min 20 30 40 50
60 80 70 90 100 110 120
• If SLLEP on the main unit is pressed, the same function as with the
remote control unit can be obtained.
To confirm the countdown time before putting the
unit to sleep
Press SLEEP .
“Z2 Sleep : zmin”, “Z3 Sleep : zmin” or “Z4 Sleep : zmin” appears
on the display.
z Countdown time
To cancel the sleep timer
Press SLEEP to set “Off”.
The sleep timer is also cancelled when this unit is set to the standby
mode or the ZONE2, ZONE3 or ZONE4 power is turned off.
NOTE
The sleep timer function cannot turn off the power of devices
connected to this unit. To turn off the power of those connected
devices, set up sleep timers on the connected devices themselves.
Basic v
ersion
A
dv
anced v
ersion
Inf
or
mations
A
dv
anced v
ersion
DVD