Tunturi T80 User Manual
Page 13
GB
O W N E R ’ S M A N U A L
•
T 8 0 T 8 5
13
4.
Spray the lubricant for 2-3 seconds.
5.
Lower the running deck into its normal position.
Use treadmill for your training session. Or allow the
treadmill to run for at least 5 minutes.
NOTE!
Lubricate your treadmill only with T-Lube
S silicon lubricant. Contact your local Tunturi
distributor for further supplies of T-Lube or further
information on lubrication and maintenance.
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually
needed, provided
•
the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to
one side due to the user’s running style (e.g. more
weight on one foot). The alignment of the belt is
adjusted by turning the two bolts at the back of the
treadmill.
ALIGN THE BELT ACCORDING TO THE FOLLOWING
INSTRUCTIONS:
1.
Turn the power switch on and increase the
treadmill’s speed to 5 km/h (3 mph).
2.
If the belt drifts to the left, turn the left adjustment
bolt ¼ turn clockwise and the right adjustment bolt
1/8 turn anti-clockwise. If the belt drifts to the right,
turn the right adjustment bolt ¼ turn clockwise and
the left adjustment bolt ¼ turn anti-clockwise.
3.
If the belt remains centered the adjustment is
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned. If the belt
is allowed run across to one side for long periods of
time the edges of the belt may be damaged and the
treadmill may not continue to operate correctly. Any
damage to the belt caused by the lack of necessary
adjustment will not be covered by the warranty.
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on
the rollers. In normal use, however, keep the belt
as loose as possible! The belt tension is adjusted by
turning the same screws as used for aligning the
running belt. If turning the screws will not effect the
belt tension, please contact your local Tunturi dealer.
1.
Increase the treadmill’s speed to 5 km/h (3 mph).
2.
Turn both adjustment screws an equal amount, ¼
turn clockwise.
3.
Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill).
If the belt slips, turn another ¼ turn and repeat the
test. When braking heavily the belt may slip. If the
belt keeps slipping despite repeated adjustments,
please contact your local Tunturi dealer.
MALFUNCTIONS
NOTE!
Despite continuous quality control, defects
and malfunctions caused by individual components
may occur in the equipment. In most cases it’s
unnecessary to take the whole device in for repair,
as it’s usually sufficient to replace the defective
part. Always give the model, serial number of
your equipment and in case of malfunctions also
conditions of use, nature of malfunction and any
error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and
ready the treadmill for normal operation again. If
after you have reset the treadmill by turning the
power switch off and on again, and the treadmill
is still not operational, contact your local Tunturi
dealer for service.
If you require spare parts, always give the model,
serial number of your equipment and the spare part
number for the part you need. The spare part list
is at the back of this manual. Use only spare parts
mentioned in the spare part list.
ERROR CODES
The user interface will display information about
operational faults.
SYSTEM CHECK FAILED. Possible motor controller
fault. Turn the power switch off, wait 1 minute and
turn the power switch on again. If treadmill recovers
to normal operation, you may continue to use the
treadmill. Otherwise, call the dealer for service.
SPEED SENSOR ERROR. Call the dealer for service.
MOTOR SPEED ERROR. Ensure correct usage of
the treadmill. Do not push the belt with your feet.
Turn the power switch off, wait 1 minute and turn
the power switch on again. If treadmill recovers
to normal operation, you may continue to use the
treadmill. Otherwise, call the dealer for service.
MOTOR OVERLOAD. Ensure correct usage of the
treadmill. Do not brake the belt. Turn the power
switch off, wait 1 minute and turn the power switch
on again. If treadmill recovers to normal operation,
you may continue to use the treadmill. Ensure the
lubrication is sufficient, re-lubricate the running
deck if needed. Otherwise, call the dealer for service.
LIFT MOTOR ERROR. Call the dealer for service.
LIFT MOTOR OVERLOAD - Ensure correct usage
of the treadmill. Do not overload the lift motor
by continuously changing the elevation. Turn the
power switch off, wait 1 minute and turn the power
switch on again. The lift motor will be automatically
calibrated when the power switch is turned on. If