Rockwell Automation 1336Z SPIDER - FRN 2.xxx-5.xxx - Manual (Page 149)

Specifications and Supplemental Information A–3
Power Dissipation
Derating Guidelines Drive ratings can be affected by a number of factors. If more than one
factor exists, derating percentages must be multiplied.
Shading indicates Drive [Rated Amps], “ * ” Indicates No Overload.
1 For 20 seconds every 10 minutes. The maximum [Current Limit] setting is shown.
2 The maximum [Current Limit] setting is shown. Normal Duty (ND) = 100%, 110% for 1 minute to 10
minutes, peak current for 3 seconds.
3 Note that parameter 13, [DC Hold Level] must NOT be set to 150%, but maximum as follows:
(A022) 140%, (A036) 140%, (A060) 100%, (B010) 70%, (B017) 70%, (B033) 70%.
4 The dynamic braking current is only defined by the external resistor. There is no internal current control
nor short circuit protection. Respective measures as bimetal relay, klixon etc have to be taken externally.
5 See Chapter 2 for dynamic brake resistor wiring information and Appendix B for dimension information.
Voltage
Catalog
Number Peak
Current
Carrier Frequency, 50 Degree C Ambient
2 kHz
4 kHz 8 kHz
Cont.
Current Power Dissipation Formula
I
L = RMS Load Current
Cont.
Current Power Dissipation Formula
I
L = RMS Load Current
Cont.
Current Power Dissipation Formula
I
L = RMS Load Current
200-240V 1336Z-xA022 21.6A 9.0A P=29W+(I L x 4.4V)+(I 2L x 0.17) 9.0A P=29W+(I L x 4.9V)+(I 2L x 0.17) 9.0A P=29W+(I L x 5.4V)+(I 2L x 0.17)
1336Z-xA036 36.0A 15.0A P=33W+(I L x 4.4V)+(I 2L x 0.10) 14.0A P=33W+(I L x 4.9V)+(I 2L x 0.10) 10.0A P=33W+(I L x 5.4V)+(I 2L x 0.10)
1336Z-xA060 60.0A 30.0A P=40W+(I L x 4.4V)+(I 2L x 0.05) 25.0A P=40W+(I L x 4.9V)+(I 2L x 0.05) 18.0A P=40W+(I L x 5.4V)+(I 2L x 0.05)
380-480V 1336Z-xB010 9.9A 8.5A P=29W+(I L x 5.5V)+(I 2L x 0.36) 5.5A P=29W+(I L x 7.8V)+(I 2L x 0.36)
1336Z-xB017 16.0A 10.0A P=33W+(I L x 5.5V)+(I 2L x 0.22) 6.0A P=33W+(I L x 7.8V)+(I 2L x 0.22)
1336Z-xB033 33.0A 17.0A P=40W+(I L x 5.5V)+(I 2L x 0.11) 10.0A P=40W+(I L x 7.8V)+(I 2L x 0.11)
Voltage
Rating
Drive
Catalog
No. Carrier
Frequency
Synch./Synch. Reluctance Motors Induction Motors
DC Brake
Current
3
Dynamic Brake
Current
4,5 F.L.A. Current Limit 1 F.L.A. Current Limit 2
kHz Ta=50˚C Ta=45˚C Ta=40˚C Peak Current Ta=50˚C Ta=45˚C Ta=40˚C Peak Current at 0 Hz A rms A DC /R min
200-240V A022 2 9A 9A 9A 21.6A = 240% 9A 9A 9A 14.4A = 160% 160% 12.6 15A/25 Ohms
4 9A 9A 9A 9A 9A 9A
8 9A 9A 9A 9A 9A 9A
A036 2 15A 15A 15A 36A = 240% 13.9A 15A 15A 24A = 160% 118% 21.0 15A/25 Ohms
4 14A 15A 15A 13A 15A 15A
8 10A 12.5A 15A 11A 13.6A 15A
A060 2 30A 30A 30A 60A = 200% 24A 28.2A 30A 48A = 160% 101% 30.0 23A/16 Ohms
4 25A 30A 30A 23A 26.5A 30A
8 18A 22A 26A 18A 23.8A 27A
380-480V B010 2 8.5A 9.9A 9.9A 9.9A = 100% 8.5A 9.9A* 9.9A* 9.9A = 100% 89% 7.0 10A/75 Ohms
4 5.5A 6.4A 7.3A 5.5A 8.4A 9.9A*
B017 2 10.0A 11.5A 13.0A 16.5A = 127% 9.5A 11.6A 13A 16.5A = 127% 105% 9.1 14A/53 Ohms
4 6.0A 7.2A 8.4A 6.0A 9.6A 11.1A
B033 2 17A 20A 23A 33A = 143% 16.8A 19.9A 23A 33A = 143% 101% 16.1 17A/43 Ohms
4 10A 12A 14A 14A 16.5A 19A
Altitude
% of Drive
Rated Amps
Altitude
m
(ft)
100%
80%
90%
0 4,000
(13,200)
3,000
(9,900)
2,000
(6,600)
1,000
(3,300)
Altitude – All Drive Ratings