Analog i/o, Analog i/o –9 – Rockwell Automation 1336Z SPIDER - FRN 2.xxx-5.xxx User Manual
Page 33
Installation/Wiring for Stand-Alone Drives
3–9
Analog I/O
The 1336 SPIDER analog I/O configuration provides a standard set of
inputs and outputs with the capability to install up to 2 option boards,
thus replacing the standard I/O with a variety of options. All
connections are performed at TB2 and TB3. Installing an option
board in the slot A or B location will change the function of those
terminals on TB2-TB3 from standard. Only one option board can be
installed in each slot. Figure 3.4 shows the standard and optional I/O
configurations.
Figure 3.4
Analog I/O – TB2 and TB3
Analog I/O Examples
1
2
3
4
5
6
7
8
9
Isolated
Input 0 (–)
10V or 20mA
Isolated
Input 0 (–)
±
10V,
±
20mA
Isolated
Input 0 (–)
±
10V,
±
20mA
Isolated
Input 0 (+)
10V or 20mA
Isolated
Input 0 (+)
±
10V,
±
20mA
Isolated
Input 0 (+)
±
10V,
±
20mA
LA2
LA6
LA7
Analog I/O Option Slot A
Analog I/O Option Slot B
Isolated
Input 1 (+)
10V or 20mA
Thermistor
Isolated
Input (+)
Isolated
Input 1 (+)
10V or 20mA
Isolated
Input 1 (–)
10V or 20mA
Thermistor
Isolated
Input (–)
Isolated
Input 1 (–)
10V or 20mA
Pot.
Reference
+5V
1
Single-Ended
Input 0
Pot., 10V or 20mA
Single-Ended
Input 1
Pot., 10V or 20mA
Signal
Common
S
i
g
n
a
l
C
o
m
m
o
n
Std.
LA1
LA3
LA4
LA5
Std.
or (select 1)
or (select 1)
Single-Ended
Input 2
2
Pot., 10V or 20mA
Isolated
Output 0 (+)
10V or 20mA
Isolated
Input 2 (+)
10V or 20mA
Single-Ended
Output 0
10V or 20mA
Single-Ended
Output 0
10V or 20mA
Isolated
Output 0 (–)
10V or 20mA
Isolated
Input 2 (–)
10V or 20mA
Non-Isolated
250 kHz
Pulse Output
Single-Ended
Output 1
20mA Only
Isolated
Output 1 (+)
10V or 20mA
Isolated
Output 1 (+)
10V or 20mA
Isolated
250 kHz
Pulse In (+)
0-20mA
Output
Return
Isolated
Output 1 (–)
10V or 20mA
Isolated
Output 1 (–)
10V or 20mA
Isolated
250 kHz
Pulse In (–)
Signal
Common
Single Ended
Output 1
0-10V Only
Single Ended
Output 0
0-10V Only
Single-Ended
Input 2
Pot., 10V or 20mA
1
If an Option Board is installed in Slot A, the +5V pot. reference will not be
available. If a 5V source is required, it must be user supplied.
2
Standard Analog Input 2 is maintained at this terminal – configure with J11.
TB2
TB3
0-10V
Standard Analog Input 2
(Non-Isolated)
Remote Potentiometer
to Standard Analog Input 0
Standard Analog Output 0
(0-10V Non-Isolated)
Isolated Input to
LA2 Option Board
Isolated Output from
LA3 Option Board
Jumper J8 Set to "Pot"
5V Ref.
+
–
Isolated Pulse Train Input
to LA5 Option Board
Pulse Train Output from LA5
Option Board (Non-Isolated)
Common
+
–
+
+
–
–
Jumper J11 Set to "0-10V"
Standard
Analog I/O
Standard Remote
Potentiometer
Optional
Pulse I/O
Optional
Analog I/O
+
–
Pulse
Source
5
6
5
6
7
1
2
1
2
3
4
5
8
9
8
9
8
7
9