Hardy HI 2151/30WC Single-Scale Controller - Manual (Page 11)

Table of Illustrations
I
Table of Illustrations
CHAPTER 1 - OVER-
VIEW MODEL NUMBER BREAKDOWN - - - - - - - - - - - - - - - - - - - - - - - - 1-8
CHAPTER 3 - INSTAL-
LATION 2” REAR PANEL CLEARANCE REQUIREMENT- - - - - - - - - - - - - - - - - 3-3
PANEL CUTOUT DIMENSIONS - - - - - - - - - - - - - - - - - - - - - - - - - 3-4
NEMA 4 GASKET FLUSH AGAINST THE FRONT PANEL- - - - - - - - - - - - 3-4
MOUNTING REMOTE DISPLAY TO ENCLOSURE - - - - - - - - - - - - - - - 3-6
INSTALLING ELECTRONICS ENCLOSURE TO A PLATE - - - - - - - - - - - - 3-6
INSTALLATION OF WALL MOUNT MODEL - - - - - - - - - - - - - - - - - - 3-7
WIRE ROUTING FOR WALL MOUNT MODEL - - - - - - - - - - - - - - - - - 3-8
POWER WIRING DIAGRAM - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-9
C2 LOAD CELL CONNECTION - - - - - - - - - - - - - - - - - - - - - - - - - 3-13
LOAD CELL CONNECTION (NON C2 LOAD CELLS) J1 - - - - - - - - - - - - - 3-14
OPTION LABEL COVER - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-15
ANALOG OUTPUT BOARD - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-16
PARALLEL BCD BOARD - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-17
BCD QUAD TERMINATION BOARD OPTION - - - - - - - - - - - - - - - - - 3-19
BCD TERMINATION BOARD INSTALLATION DRILL TEMPLATE - - - - - - - 3-19
BCD TERMINATION INSTALLATION BLOCK DIAGRAM - - - - - - - - - - - 3-20
RIO CARD/PIN LAYOUT- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-21
SET POINT RELAY OPTION BOARD - - - - - - - - - - - - - - - - - - - - - - 3-23
INSTALLATION DETAILS - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-23
STANDOFF ASSEMBLY - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-23
SECURE MEMORY MODULE - - - - - - - - - - - - - - - - - - - - - - - - - - 3-24
INSTALLING AND REMOVING THE SECURE MEMORY MODULE - - - - - - 3-24
CHAPTER 4 - SYSTEM
CONFIGURATION MAIN BOARD JUMPER AND DIP SWITCH LOCATIONS - - - - - - - - - - - - 4-1
REMOVING THE REAR PANEL - - - - - - - - - - - - - - - - - - - - - - - - - 4-2
RS-232 (DEFAULT), S422/485 JUMPER SETTINGS - - - - - - - - - - - - - - - 4-3
NON TERMINATING CONTROLLER, ALL DIP SWITCHES SET
IN THE OFF POSITION- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3
TERMINATING CONTROLLER, ALL DIP SWITCHES SET
IN THE ON POSITION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-4
ANALOG OUTPUT BOARD - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-6
BCD CARD JUMPER LOCATION - - - - - - - - - - - - - - - - - - - - - - - - 4-6
BCD JUMPER SETTINGS - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-7
CAL TOGGLE SWITCH LOCATION - - - - - - - - - - - - - - - - - - - - - - - 4-7
AUTO ZERO DIP SWITCH SETTING- - - - - - - - - - - - - - - - - - - - - - - 4-8
PEAK HOLD MODE DIP SWITCH LOCATION- - - - - - - - - - - - - - - - - - 4-9
POWER & RELAY BOARD DIP SWITCH LOCATION - - - - - - - - - - - - - - 4-10
CHAPTER 5 - SETUP FRONT PANEL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
FRONT PANEL, BAR GRAPH DISPLAYED - - - - - - - - - - - - - - - - - - - 5-3
CHAPTER 6 - CALI-
BRATION PROPERLY INSTALLED LOAD CELL W/NO BINDING - - - - - - - - - - - - - 6-2
MILLIVOLTS/WEIGHT SCALE - - - - - - - - - - - - - - - - - - - - - - - - - 6-3
FRONT PANEL DISPLAY WITH NUMBERS - - - - - - - - - - - - - - - - - - - 6-4
FRONT PANEL DISPLAY WITH TEXT - - - - - - - - - - - - - - - - - - - - - 6-4
FRONT PANEL STATUS LEDS DISPLAYED- - - - - - - - - - - - - - - - - - - 6-5
CHAPTER 7 - OPERA-
TION FRONT PANEL, PROCESS WEIGHING FUNCTION BUTTONS - - - - - - - - - 7-1
OPTION MENU TREE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
LOW AND HIGH PREACT TRIP LIMITS - - - - - - - - - - - - - - - - - - - - - 7-5
WIRING DIAGRAM SERIAL COMMUNICATIONS - - - - - - - - - - - - - - - 7-8