Document Outline

• EG – declaration of conformity
• Product registration
• 1. Safety
  • 1.1 Legal considerations
  • 1.2 Structure of the safety instructions
    • 1.2.1 Signal word panel
    • 1.2.2 Safety alert symbol
    • 1.2.3 Pictograms
    • 1.2.4 Word message panel structure
  • 1.3 Localization / position of safety labels on the unit
  • 1.4 Type plate
  • 1.5 General safety instructions on installing and operating the refrigerated incubator
  • 1.6 Intended use
• 2. Unit description
  • 2.1 Unit overview
  • 2.2 Instrument panel
  • 2.3 Unit rear
• 3. Completeness of delivery, transportation, storage, and location of installation
  • 3.1 Unpacking, and checking equipment and completeness of delivery
  • 3.2 Guidelines for safe lifting and transportation
  • 3.3 Storage
  • 3.4 Location of installation and ambient conditions
• 4. Installation of the equipment
  • 4.1 Spacer for wall distance
  • 4.2 Electrical connection
• 5. Start up
• 6. Functional overview of the T4.12 chamber controller
  • 6.1 Menu structure
    • 6.1.1 General menu
    • 6.1.2 Quick menu
    • 6.1.3 “User” menu
  • 6.2 Operating modes
    • 6.2.1 Activating the “control off” mode or change to “fixed value” operating mode
  • 6.3 Performance during and after power failure
  • 6.4 Information
• 7. Configuration of optional equipment
  • 7.1 Setting the optional door heating
  • 7.2 Turning on / off the optional interior socket
  • 7.3 Switching on or off the optional zero-voltage relay control outputs
  • 7.4 Functional test of the optional alarm output
  • 7.5 Switching on or off the optional object temperature display
• 8. Set-point entry in “Fixed value” operating mode
  • 8.1 Setting ranges:
  • 8.2 Entering the set-points via “quick menu”
  • 8.3 Entering the set-points via general menu
• 9. Time programs
  • 9.1 Starting and running an existing time program
  • 9.2 Cancelling a running time program
  • 9.3 Creating a new time program
    • 9.3.1 Section handling
    • 9.3.2 Temperature setpoint
    • 9.3.3 Section duration
    • 9.3.4 Repeating one or several sections within a time program
    • 9.3.5 Tolerance range
    • 9.3.6 Set-point ramp and set-point step modes
    • 9.3.7 Switching on or off the optional zero-voltage relay outputs
    • 9.3.8 Calling up the next parameter
    • 9.3.9 Saving the time program and leaving the program editor
  • 9.4 Program interruption
  • 9.5 Deleting a time program
• 10. Week programs
  • 10.1 Starting and running an existing week program
  • 10.2 Cancelling a running week program
  • 10.3 Creating a new week program
    • 10.3.1 Section handling
    • 10.3.2 Temperature setpoint
    • 10.3.3 Day of the week
    • 10.3.4 Time of the day
    • 10.3.5 Activity of the shift-point
    • 10.3.6 Switching on or off the optional zero-voltage relay outputs
    • 10.3.7 Calling up the next parameter
    • 10.3.8 Saving the week program and leaving the program editor
  • 10.4 Deleting a week program
• 11. Key lock
  • 11.1 Directly activating the key lock function
  • 11.2 Automatic key lock
  • 11.3 Changing the password for unlocking the key lock
• 12. General controller settings
  • 12.1 Setup wizard
  • 12.2 Date and time settings
  • 12.3 Selecting the menu language of the T4.12 controller
  • 12.4 Setting display brightness
  • 12.5 Changing the temperature unit
  • 12.6 Defining the data recording rate
  • 12.7 Factory reset
  • 12.8 Network configuration
  • 12.9 Display of the entire network configuration
  • 12.10 MAC Address
  • 12.11 RS 422 address (with optional RS 422 interface)
  • 12.12 Display and entry of the chamber configuration – for service purpose
• 13. Data transfer via USB interface
  • 13.1 Exporting data to USB drive
  • 13.2 Importing data from USB drive
• 14. Notifications and Alarms
  • 14.1 Notifications overview
  • 14.2 Alarms overview
  • 14.3 Confirming an active alarm
  • 14.4 Alarm configuration and overview
    • 14.4.1 List of active alarms
    • 14.4.2 History – list of all alarms
    • 14.4.3 Activating, deactivating, and testing the alarm buzzer
    • 14.4.4 Activating / deactivating all alarm functions
• 15. Event list
• 16. Graphical display of the measured values
  • 16.1 Setting the sampling rate
  • 16.2 Defining the display range
  • 16.3 Selecting the parameters
• 17. Temperature safety devices
  • 17.1 Overtemperature protective device (class 1)
  • 17.2 Overtemperature safety controller (temperature safety device class 3.1)
    • 17.2.1 Safety controller modes
    • 17.2.2 Setting the safety controller
  • 17.3 Over- and undertemperature safety controller (temperature safety device class 3.3) (option)
    • 17.3.1 Safety controller modes
    • 17.3.2 Setting the Safety controller
• 18. Notes on refrigerating operation
• 19. Options
  • 19.1 Communication software APT-COM™ 3 DataControlSystem (option)
  • 19.2 RS 422 interface (option)
  • 19.3 Data logger kit (option)
  • 19.4 Object temperature display with flexible Pt 100 temperature sensor (option)
  • 19.5 Zero-voltage relay alarm output (option)
  • 19.6 Analog output for temperature (option)
  • 19.7 Zero-voltage relay control outputs (option)
  • 19.8 Water protected internal socket (option)
• 20. Maintenance, cleaning, and service
  • 20.1 Maintenance intervals, service
  • 20.2 Cleaning and decontamination
    • 20.2.1 Cleaning
  • 20.3 Sending the unit back to BINDER GmbH
• 21. Disposal
  • 21.1 Disposal of the transport packing
  • 21.2 Decommissioning
  • 21.3 Disposal of the unit in the Federal Republic of Germany
  • 21.4 Disposal of the unit in the member states of the EC except for the Federal Republic of Germany
  • 21.5 Disposal of the unit in non-member states of the EC
• 22. Troubleshooting
• 23. Technical description
  • 23.1 Factory calibration and adjustment
  • 23.2 Over current protection
  • 23.3 Definition of usable volume
  • 23.4 KT technical data
  • 23.5 Equipment and Options
  • 23.6 Spare parts and accessories
  • 23.7 Dimensions KT 53
  • 23.8 Dimensions KT 115
• 24. Contamination clearance certificate
  • 24.1 For units located outside North America and Central America
  • 24.2 For units in North America and Central America
• Word-Lesezeichen
  • OLE_LINK6
  • OLE_LINK7
  • OLE_LINK8
  • OLE_LINK9