Marantz AV8003 User Manual
Page 39
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
SETUP
36
ENGLISH
5-1 ZONE SETUP
The AV8003 has source selectors, sleep timers and
zonespeaker output remote controller for the two
other ZONEs in the zone system.
These features can be set from this menu.
1.
Select
“5. PREFERENCE” from the MAIN
MENU with the
3
or
4
cursor buttons and
press the ENTER button.
2.
Select
“ZONE SETUP” with the
3
or
4
cursor
buttons and select either “ZONE A” or “ZONE
B” with the
1
or
2
cursor buttons.
3.
Press
the
ENTER button to enter the setting.
The following explanation shows how to operate
ZONE A of the zone system.
The ZONE B setting does not have the VIDEO
FUNCTION.
Z O N E S E T U P A
V I D E O :
D V D
A U D I O : D V D
S L E E P : O F F
M O N O / S T : S T E R E O
O S D I N F O : E N A B L E
Z O N E : O F F S P K R :
V O L : V A R I V O L :
L E V : - 9 0 d B L E V :
R E T U R N B A C K E X I T
4.
Select the desired item with the
3
or
4
cursor
button.
VIDEO:
Select the video source of the zone output with the
1
or
2
cursor buttons.
AUDIO:
Select the audio source of the zone output with the
1
or
2
cursor buttons.
SLEEP:
The sleep mode is available when the zone is
active, set the time with
1
or
2
cursor buttons. The
sleep timer can be set to a maximum 120 minutes
in 10 minute increments.
MONO/ST:
This mode switches audio output to the zone
system between MONAURAL and STEREO,
using the
1
and
2
cursor buttons.
OSD INFO:
With this function, on-screen display information is
shown on connected TVs or other devices when
you switch input functions. Select “ENABLE” with
the
1
or
2
cursor buttons to enable OSD INFO or
“DISABLE” to disable it. Select “DISABLE” if this
function is not needed.
ZONE:
Switch the zone output “ON” or “OFF” with the
1
or
2
cursor buttons.
SPKR (ZONE SPEAKER):
Switch the speaker output “ON” or “OFF” with the
1
or
2
cursor buttons.
VOL (VOLUME SETUP):
Select whether the zone or zone speaker output
level is variable or fi xed with the
1
or
2
cursor
buttons.
LEVEL (VOLUME LEVEL):
Adjust the zone output level with the
1
or
2
cursor
buttons. The volume can be set between -90 dB
and 0 dB in 1 dB increments.
Note:
• SPKR setting can be changed when the SURR B is
set to “NONE” in the SPEAKER SIZE menu and
“SPEAKER C” is in the OFF position on the rear
panel. When this setting is unavailable, “***” is
displayed.
• If “VOLUME” is set to “FIXED”, the zone output
level cannot be adjusted from the A or B ZONE.
• SPKR cannot be on for both ZONE A and ZONE
B at the same time. After you complete this portion
of the setup, move the cursor to “RETURN” with
the
3 or 4 cursor buttons and press the ENTER
button.
5-2 DC TRIGGER SETUP
This unit has 2 DC trigger control jacks, which can
be used to link with input functions for the main zone
or zone.
Each trigger can be setup separately.
1.
Select
“5. PREFERENCE” from MAIN MENU
with the
3
or
4
cursor buttons and press the
ENTER button.
2.
Select
“DC TRIGGER SETUP 1or 2” with the
3
,
4
,
1
and
2
cursor buttons.
3.
Press the ENTER button to enter the
selection.
D C T R I G G E R S E T U P
D C T R I G - 1 :
D I S A B L E
T V : T A P E :
D V D : C D / R :
V C R 1 : A U X :
D S S : T U N E R :
N E T : 7 . 1 C H :
R E T U R N
N E X T
E X I T
4.
You can select “MAIN ZONE”, “ZONE A”,
“ZONE B”, “REMOTE” or “DISABLE” with the
1
or
2
cursor buttons.
Note:
• REMOTE is available for the external control. The
RC2001 cannot operate the function.
5.
Select desired input source with the
3
or
4
cursor buttons.
6.
Set
to
“ON” or “OFF” with the
1
or
2
cursor
buttons.
7.
After you complete this portion of the setup,
move the cursor to “RETURN” with the
3
or
4
cursor button and press the ENTER button.
Note:
• When an input source that is on in the set ZONE
is selected, voltage is output to the DC TRIGGER
output terminal.
AV8003_U_Eng.indb 36
AV8003_U_Eng.indb 36
08.4.28 10:40:15 AM
08.4.28 10:40:15 AM