Marantz AV8003 - Manual (Page 50)

CONNECTIONS
SETUP
BASIC
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
47
ENGLISH
AUX INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX input.
In this case, You can connect additional audio source
to AUX as other audio input terminals.
TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX
MODE MODE SURROUND SURROUND CLEAR MEMORY T-MODE BAND EXIT MENU ZONE ZONE
DOWN
VOLUME
UP
INPUT INPUT SELECTOR SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF POWER ON/OFF
STANDBY STANDBY
AV PRE TUNER AV8003
ENTER
To select AUX, turn the INPUT SELECTOR knob on
the front panel, or press HOME button and press 6
button on remote controller.
VIDEO ON/OFF
When no video signal is connected to the unit or
a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, switch the remote controller to
AMP mode and press the < / > button until 004 is
displayed. Then press the VIDEO OFF button.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX M-DAX
MODE SURROUND CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN
VOLUME
UP
INPUT SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF
STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
V-OFF
The “V-OFF” indicator on the main unit display panel
will light.
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.
AUTO POWER ON
1. Be sure the TV auto mode is ENABLED. (Refer
to page 34)
2. Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3. Turn OFF the power to the TV TUNER and the
unit.
4. Turn ON the TV TUNER and tune in a receivable
station.
5. When the station is received, this unit turns ON
and TV is selected automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2. The power to the unit switches to STANDBY
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if this unit is set to
a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
• This function is inactive when STANDBY MODE
is set to ECONOMY. To use this function, set
STANDBY MODE to NORMAL.
LIP.SYNC
Depending on the image device (TV, monitor,
projector, etc.) connected to the unit a time lag can
occur between image signal processing and audio
signal processing. Though minor, this time lag can
interfere with movie and music enjoyment. The LIP.
SYNC feature delays the audio signal with respect
to the image signal output from the unit to correct
the time lag between the sound and image. It can be
operated with the “LIP.SYNC” and
1 and 2 cursor
buttons of the remote controller. To select Lip-sync
mode, set the remote controller to the AMP mode,
press the < / > button until 002 is displayed. Press
the LIP. SYNC button. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
• The LIP.SYSNC feature turns OFF (0 ms) in
the SOURCE/PURE DIRECT mode. When the
SOURCE/PURE DIRECT mode is deactivated, the
set value of the LIP.SYSNC feature is automatically
restored.
• Even if you do not correct the time lag manually this
way, audio and video are automatically synchronized
when the unit is connected to TV or Projector
supporting Auto Lipsync Correction in HDMI 1.3a.
For instructions on Auto Lipsync Correction, see
page 35.
DUAL BACKUP MEMORY
The unit stores settings information in nonvolatile
memory even when the main power supply is turned
off. Using the Dual Backup Memory function, you
can write settings information to another memory
area to back up saved settings for recovery anytime
as needed.
BACKUP
Set up the unit in the state for which you want to
store the settings. Hold the MEMORY and ENTER
buttons on the front panel simultaneously for at least
3 seconds.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT PURE
PHONES
THX M-DAX M-DAX
MODE SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT SELECTOR
AUTO
SETUP MIC
HDMI HDMI
M-DAX
PURE DIRECT
POWER ON/OFF STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
“MEMORY SAVING” is displayed and the unit’s
settings are saved. The stored settings information
is retained until Dual Backup Memory is used again
and the information is overwritten.
M E M O R Y S A V I N G
Note:
• The following settings values cannot be backed
up.
• Main Zone Volume
•
Zone Volume
• Zone Speaker Volume
AV8003_U_Eng.indb 47 AV8003_U_Eng.indb 47 08.4.28 10:40:24 AM 08.4.28 10:40:24 AM