Marantz AV8003 - Manual (Page 61)

CONNECTIONS
SETUP
BASIC
OPERA
TION
REMOTE
CONTROLLER
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
58
ENGLISH
CATEGORY SEARCH MODE
You can select the desired channel from the category
allocated to each channel.
Category being aired can be only selected.
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT DIRECT PURE PURE
PHONES PHONES
THX THX M-DAX M-DAX
MODE MODE SURROUND SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT INPUT SELECTOR SELECTOR
AUTO AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX M-DAX
PURE DIRECT PURE DIRECT
POWER ON/OFF POWER ON/OFF
STANDBY STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
3. 3.
2. 2.
4.
4.
5.
(Using the unit)
1. Press the ENTER button on the front panel.
2. Press the 1 or 2 button on the front panel to
select the desired Category.
3. After selecting the Category, Press the 3 or 4
cursor button to select the desired station of the
category.
4. You can return to the normal mode by press the
ENTER button during Category Search Mode.
(Using the remote controller)
1. Switch the remote controller to TUNER mode.
2. Press the < / > button until 003 is display.
3. Press the SAT CAT + / − button.
4. After selecting the category, Press the 3 or 4
cursor button to select the desired station of the
category.
5. You can return to the normal mode by press the
ENTER button during Category Search Mode.
Note:
• Category search ends automatically about 5 seconds
after the last operation.
CHANNEL DIRECT CALL
You can select the desired channel by directly tapping
the numeric keypads on the remote controller.
2.
3.
1. Switch the remote controller to TUNER mode.
2. Press the GUIDE button.
“XM - - -” will appear on the display.
3. Input the three digit number for your desired
Channel with the numeric keypad on the
remote controller.
4. The desired channel will automatically be
tuned.
Note:
• If there is no input on the keypad for 5sec., the input
is cancelled to return to the original display
Notes:
• “LOADING” is displayed while receiving the
channel or information.
• “UPDATING” is displayed while updating encryption
code.
• When the selected channel is not available, “XM - -
-” is dispIayed.
• “OFF AIR” is displayed while air is suspended (e.g.
midnight).
PRESET MEMORY
You can store the desired channel in the Preset
Memory.
(You can preset 50 XM Radio stations in addition to
FM/AM stations.)
TOP TOP
ZONE ZONE SPEAKER SPEAKER
DISPLAY DISPLAY INPUT INPUT 7.1CH 7.1CH DIRECT PURE
PHONES
THX THX M-DAX M-DAX
MODE SURROUND CLEAR CLEAR MEMORY MEMORY T-MODE T-MODE BAND BAND EXIT EXIT MENU MENU ZONE ZONE
DOWN DOWN
VOLUME VOLUME
UP UP
INPUT SELECTOR
AUTO
SETUP MIC SETUP MIC
HDMI HDMI
M-DAX
PURE DIRECT
POWER ON/OFF
STANDBY
AV PRE TUNER AV8003 AV PRE TUNER AV8003
ENTER ENTER
3. 2. 4.
3. 3.
2. 2.
4.
(Using the unit)
1. Tune into the desired channel.
2. Press the MEMORY button on the front panel.
”- -” (preset number) starts blinking on the
dispIay.
- - X M 0 4 0
3. Select the preset number by pressing the 1
or 2 cursor buttons, While this is still blinking
(approx. 5 seconds)
0 1 X M 0 4 0
4. Press the MEMORY button again to enter.
The display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
1. Tune into the desired channel.
2. Press the < / > button until 002 is display.
3. Press the MEMORY button on the remote
controller. “- -” (preset number) starts blinking
on the display.
4. Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
AV8003_U_Eng.indb 58 AV8003_U_Eng.indb 58 08.4.28 10:40:31 AM 08.4.28 10:40:31 AM