Document Outline

• PREFACE
• Contents
• 1 Precautions Relating to Use
• 2 Names of Component Parts
  • 2.1 Main Unit
  • 2.2 Operation Keys
  • 2.3 Displayed Signs
    • 2.3.1 Displayed signs
• 3 Installation of the Balance
  • 1. Attach the pan base and pan.
  • 2. Level the Balance.
  • 3. Connect the AC adapter.
• 4 Basic Operation
  • 4.1 Power On/Off
  • 4.2 Weighing
  • 4.3 Zero Adjustment
  • 4.4 Tare (pan)
  • 4.5 Set a Gross Weight
  • 4.6 Single-touch Response Setting
  • 4.7 Data Output
  • 4.8 Hanging Measurement
• 5 Function 1
  • 5.1 Setting and Check
    • 1. Call Function 1.
    • 2. Select the next setting item.
    • 3. Change settings.
    • 4. Complete the setting of functions.
  • 5.2 Description of Function 1
  • 5.3 Specific Gravity Setting
  • 5.4 Limit/Addition Functions
  • 5.5 Interface
• 6 Function 2
  • 6.1 Calling and Setting
    • 1. Call Function 2.
    • 2. Change settings.
    • 3. Complete the setting of functions.
  • 6.2 Description of Function 2
• 7 Weighing and Measurement Modes
  • 7.1 Weighing and Measurement Modes
  • 7.2 Weighing Machine
• 8 Parts Counting
  • 1. Start sampling.
  • 2. Change the number of samples as required.
  • 3. Put a sample on the balance.
  • 4. Put additional samples on the balance.
  • 5. Finish sampling.
  • 6. Counting the number of samples.
• 9 Percentage Weighing
  • 9.1 Set a reference weight by weighing an actual sample
    • 1. Start sampling.
    • 2. Put a sample on the balance.
    • 3. Save the reference weight.
    • 4. Put a sample to weigh on the balance.
  • 9.2 Set a reference weight by entering a value
    • 1. Displaying a reference sample weight.
    • 2. Enter a reference weight.
    • 3. Select a number.
    • 4. Select digit places to specify a reference weight.
    • 5. Save the reference weight.
    • 6. Put a sample to weigh on the balance.
• 10 Unit Converting
  • 1. Displaying the coefficient setting.
  • 2. Enter a coefficient.
  • 3. Changing numbers.
  • 4. Select digit places to specify a coefficient.
  • 5. Save the coefficient.
  • 6. Put a sample to weigh on the balance.
• 11 Gravimeter
  • 11.1 Measurement procedures for specific gravity
    • 1. Preparation for specific gravity measurements.
    • 2. Measure the water temperature in the container and enter the value into the balance.
    • 3. Reset the display to “0”.
    • 4. Measure the weight of the sample in the air.
    • 5. Submerge only the hanging cage and set to “0”.
    • 6. Measure the weight of the sample in water.
    • 7. Displaying specific gravity
    • 8. Return to weight display.
  • 11.2 Entering water temperature or the specific gravity of the media
    • 1. Call the mode to enter a correction value.
    • 2. Begin entering a value.
    • 3. Enter the value.
    • 4. Save the value.
  • 11.3 Gravimeter measurement data output
• 12 Addition Function
  • 12.1 Cumulate Function
    • 1. Reset the display to 0.
    • 2. Put samples on the balance, and obtain the weight.
    • 3. Put another sample on the balance.
    • 4. Read the weight.
    • 5. Display the cumulative weight.
    • 6. Clear the cumulative weight.
  • 12.2 Net Addition Function
    • 1. Reset the display to “0”.
    • 2. Put samples on the balance, and obtain the weight.
    • 3. The balance automatically sets tare range.
    • 4. Put additional samples on the balance to obtain the weight.
    • 5. Display the cumulative weight.
    • 6. Clear the cumulative weight.
• 13 Limit Function
  • 13.1 Setting the Limit Function
  • 13.2 Judgment and Saving
  • 13.3 Display of Judgment Results
  • 13.4 Judge by Absolute Values
    • 13.4.1 Set two limit values by putting actual samples on the balance ( Judge by Absolute Values (
      • 1. Start the limit function.
      • 2. Put the lower limit sample on the balance.
      • 3. Save the lower limit.
      • 4. Set an upper limit.
      • 5. Put the upper limit sample on the balance.
      • 6. Save the upper limit.
    • 13.4.2 Set two limit values by entering values
      • 1. Switch to the setting screen of limit values.
      • 2. Enter a numerical value.
      • 3. Select a number.
      • 4. Select a digit to enter a value
      • 5. Save the lower limit.
      • 6. Setting an upper limit
  • 13.5 Judge by Deviation Values
    • 13.5.1 Set two limit values by putting actual samples on the balance ( Judge by Deviation Values (
      • 1. Start limit value setting.
      • 2. Enter a reference weight.
      • 3. Enter a lower limit value.
      • 4. Enter an upper limit value.
    • 13.5.2 Set two limit values by entering values ( Judge by Deviation Values (
      • 1. Start limit value setting.
      • 2. Switch to the value input screen.
      • 3. Enter a reference weight.
      • 4. Enter a lower limit value.
      • 5. Enter an upper limit value.
  • 13.6 Bar Graph for the 2-point Scale
• 14 Calibration and Span Test for the Balance
  • 14.1 Span Adjustment with Built-In Weights
    • 1. Press the Cal key.
    • 2. When [PuSH C] is displayed, press the Cal key again.
  • 14.2 Span Adjustment with External Weight
    • 1. Press the Cal key.
    • 2. When [PuSH C] is displayed, press the Cal key again.
    • 3. When [on F.S.] is displayed, put a weight on the pan.
  • 14.3 Span Test with Built-In Weights
    • 1. Press the Cal key.
    • 2. When [PuSH C] is displayed, press the Cal key again.
  • 14.4 Span Test with External Weight
    • 1. Press the Cal key.
    • 2. When [PuSH C] is displayed, press the Cal key again.
    • 3. When [on F.S.] is displayed, put a weight on the pan.
  • 14.5 Calibration of Built-In Weights
  • 14.6 Entry of Weight Error
    • 1. Select [2. o.NP. 1] in Function 2.
    • 2. Display the weight error.
    • 3. Start entering the weight error.
    • 4. Enter a numerical values.
    • 5. Save the weight error
  • 14.7 Advice CAL and Full-automatic Span Adjustment
  • 14.8 Auto Repeatability Measurement (ARM)
• 15 Date and Time Setup
  • 15.1 Time Setup
    • 1. Display the time.
    • 2. Set the time.
    • 3. Save the time.
  • 15.2 Date Setup
    • 1. Display the date.
    • 2. Set a date.
    • 3. Save the date.
• 16 Various Functions
  • 16.1 Auto-Zero (Zero Tracking)
  • 16.2 Auto Backlight OFF
  • 16.3 Auto Power Off
  • 16.4 Set Unit
  • 16.5 Minimum Readability Setting
  • 16.6 Date Display
  • 16.7 Time Stamp Output
  • 16.8 Save Tare Weight Function
  • 16.9 Direct Start
  • 16.10 Interval Output Function
    • 1. Call the interval function.
    • 2. Set an interval.
    • 3. Save the settings, and go back to measurement mode.
  • 16.11 Input of ID No.
    • 1. Select [1. 1d 1] in Function 2.
    • 2. Display an ID number.
    • 3. Start to enter an ID number.
    • 4. Enter an ID number.
    • 5. Save the ID number.
• 17 Input/Output Functions
  • 17.1 RS232C Output
    • 17.1.1 Connector pin numbers and functions
    • 17.1.2 Connecting between the balance and a PC
    • 17.1.3 Interface specifications
  • 17.2 Type of Communication Texts
  • 17.3 Output Data
    • 17.3.1 Data format
    • 17.3.2 Polarity (P1: 1 character)
    • 17.3.3 Numeric data
    • 17.3.4 Unit (U1, U2: 2 characters)
    • 17.3.5 Judgment result when the limit function is enabled (S1: 1 character)
    • 17.3.6 Status (S2:1 character)
    • 17.3.7 Output data other than measurement data
  • 17.4 Input Commands
    • 17.4.1 Procedure for transmission
    • 17.4.2 Response
    • 17.4.3 Command format
    • 17.4.4 Set measurement mode command
    • 17.4.5 Request date or time output command
    • 17.4.6 Setting intervals
    • 17.4.7 Span adjustment/test command
    • 17.4.8 Setting limit values
    • 17.4.9 Sample input commands
  • 17.5 Special Format Output
    • 17.5.1 Special format 1
    • 17.5.2 Special format 2
• PC9801
• 18 Use Printers
  • 18.1 Setting up the Printer
  • 18.2 Outputting calibration results
  • 18.3 Output of Measurement Data in Compliance with ISO/GLP/GMP
    • 1. Set Function 1.
    • 2. Header output.
    • 3. Measurement data output.
    • 4. Footer output.
• 19 Output in Compliance with ISO/GLP/GMP
• 20 Removing the Windshield Door
  • 20.1 Removing the Windshield Door
    • 1. Remove the pan and pan base.
  • 20.2 Caring for the balance
• 21 Operate on Batteries
• 22 Troubleshooting
• 23 Specifications
  • 23.1 Basic Specifications
  • 23.2 Weighing Capacity and Minimum Readability by Unit
• 24 Unit Conversion Table
• TA Series Limited Warranty