Document Outline

• Contents
• Preface
• Safety and Tools
  • 1.1 Safety Precautions
  • 1.2 System Precautions
    • 1.2.1 Electrical Safety Precautions
    • 1.2.2 Equipment Rack Safety Precautions
    • 1.2.3 Filler Boards and Filler Panels
    • 1.2.4 Handling Components
• Fault Isolation
  • 2.1 Determining Which Diagnostics Tools to Use
  • 2.2 Checking the Server and System Configuration
    • 2.2.1 Checking the Hardware Configuration and FRU Status
      • 2.2.1.1 Checking the Hardware Configuration
    • 2.2.2 Checking the Software and Firmware Configuration
      • 2.2.2.1 Checking the Software Configuration
      • 2.2.2.2 Checking the Firmware Configuration
    • 2.2.3 Downloading the Error Log Information
  • 2.3 Operator Panel
  • 2.4 Error Conditions
    • 2.4.1 Predictive Self-Healing Tools
    • 2.4.2 Monitoring Output
    • 2.4.3 Messaging Output
  • 2.5 LED Functions
  • 2.6 Using the Diagnostic Commands
    • 2.6.1 Using the showlogs Command
    • 2.6.2 Using the fmdump Command
      • 2.6.2.1 fmdump -V Command
      • 2.6.2.2 fmdump -e Command
    • 2.6.3 Using the fmadm faulty Command
      • 2.6.3.1 fmadm repair Command
      • 2.6.3.2 fmadm config Command
    • 2.6.4 Using the fmstat Command
  • 2.7 Traditional Solaris Diagnostic Commands
    • 2.7.1 Using the iostat Command
      • 2.7.1.1 Options
    • 2.7.2 Using the prtdiag Command
      • 2.7.2.1 Options
    • 2.7.3 Using the prtconf Command
      • 2.7.3.1 Options
    • 2.7.4 Using the netstat Command
      • 2.7.4.1 Options
    • 2.7.5 Using the ping Command
      • 2.7.5.1 Options
    • 2.7.6 Using the ps Command
      • 2.7.6.1 Options
    • 2.7.7 Using the prstat Command
      • 2.7.7.1 Options
  • 2.8 Other Issues
    • 2.8.1 Can’t Locate Boot Device
• Periodic Maintenance
  • 3.1 Tape Drive Unit
    • 3.1.1 Cleaning the Tape Drive Unit
• FRU Replacement Preparation
  • 4.1 FRU Replacement Method
  • 4.2 Active Replacement
    • 4.2.1 Removing a FRU From a Domain
    • 4.2.2 Removing and Replacing a FRU
    • 4.2.3 Adding a FRU Into a Domain
    • 4.2.4 Verifying Hardware Operation
  • 4.3 Hot Replacement
    • 4.3.1 Removing and Replacing a FRU
    • 4.3.2 Verifying Hardware Operation
  • 4.4 Cold Replacement (Powering the Server Off and On)
    • 4.4.1 Powering the Server Off Using Software
    • 4.4.2 Powering the Server On Using Software
    • 4.4.3 Powering the Server Off Manually
    • 4.4.4 Powering the Server On Manually
    • 4.4.5 Verifying Hardware Operation
• Internal Components Access
  • 5.1 Sliding the Server In and Out to the Fan Stop
    • 5.1.1 Sliding the Server Out of the Equipment Rack
    • 5.1.2 Sliding the Server Into the Equipment Rack
  • 5.2 Top Cover Remove and Replace
    • 5.2.1 Removing the Top Cover
    • 5.2.2 Replacing the Top Cover
  • 5.3 Fan Cover Remove and Replace
    • 5.3.1 Removing the Fan Cover
    • 5.3.2 Replacing the Fan Cover
• Storage Devices Replacement
  • 6.1 Hard Disk Drive Replacement
    • 6.1.1 Accessing the Hard Disk Drive
    • 6.1.2 Removing the Hard Disk Drive
    • 6.1.3 Installing the Hard Disk Drive
    • 6.1.4 Securing the Server
    • 6.1.5 Accessing the Hard Disk Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.1.6 Removing the Hard Disk Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.1.7 Installing the Hard Disk Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.1.8 Securing the Server
    • 6.1.9 Accessing the Hard Disk Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.1.10 Removing the Hard Disk Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.1.11 Installing the Hard Disk Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.1.12 Securing the Server
  • 6.2 CD-RW/DVD-RW Drive Unit (DVDU) Replacement
    • 6.2.1 Accessing the CD-RW/DVD-RW Drive Unit
    • 6.2.2 Removing the CD-RW/DVD-RW Drive Unit
    • 6.2.3 Installing the CD-RW/DVD-RW Drive Unit
    • 6.2.4 Securing the Server
    • 6.2.5 Accessing the CD-RW/DVD-RW Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.2.6 Removing the CD-RW/DVD-RW Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.2.7 Installing the CD-RW/DVD-RW Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.2.8 Securing the Server
    • 6.2.9 Accessing the CD-RW/DVD-RW Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.2.10 Removing the CD-RW/DVD-RW Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.2.11 Installing the CD-RW/DVD-RW Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.2.12 Securing the Server
  • 6.3 Tape Drive Unit Replacement
    • 6.3.1 Accessing the Tape Drive Unit
    • 6.3.2 Removing the Tape Drive Unit
    • 6.3.3 Installing the Tape Drive Unit
    • 6.3.4 Securing the Server
    • 6.3.5 Accessing the Tape Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.3.6 Removing the Tape Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.3.7 Installing the Tape Drive Backplane of the SPARC Enterprise M4000 Server
    • 6.3.8 Securing the Server
    • 6.3.9 Accessing the Tape Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.3.10 Removing the Tape Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.3.11 Installing the Tape Drive Backplane of the SPARC Enterprise M5000 Server
    • 6.3.12 Securing the Server
• Power Systems Replacement
  • 7.1 Power Supply Unit Replacement
    • 7.1.1 Accessing the Power Supply Unit
    • 7.1.2 Removing the Power Supply Unit
    • 7.1.3 Installing the Power Supply Unit
    • 7.1.4 Securing the Server
• I/O Unit Replacement
  • 8.1 PCI Cassette Replacement
    • 8.1.1 Accessing the PCI Cassette
    • 8.1.2 Removing the PCI Cassette
    • 8.1.3 Installing the PCI Cassette
    • 8.1.4 Securing the Server
  • 8.2 PCI Card Replacement
    • 8.2.1 Removing the PCI Card
    • 8.2.2 Installing the PCI Card
  • 8.3 I/O Unit Replacement
    • 8.3.1 Accessing the I/O Unit
    • 8.3.2 Removing the I/O Unit
    • 8.3.3 Installing the I/O Unit
    • 8.3.4 Securing the Server
  • 8.4 I/O Unit DC-DC Converter Replacement
    • 8.4.1 Accessing the I/O Unit DC-DC Converter (DDC_A#0 or DDC_B#0)
    • 8.4.2 Removing the I/O Unit DC-DC Converter (DDC_A #0 or DDC_B #0)
    • 8.4.3 Installing the I/O Unit DC-DC Converter (DDC_A #0 or DDC_B #0)
    • 8.4.4 Securing the Server
    • 8.4.5 Accessing the I/O Unit DC-DC Converter Riser
    • 8.4.6 Removing the I/O Unit DC-DC Converter Riser
    • 8.4.7 Replacing the I/O Unit DC-DC Converter Riser
    • 8.4.8 Securing the Server
• XSCF Unit Replacement
  • 9.1 XSCF Unit Replacement
    • 9.1.1 Accessing the XSCF Unit
    • 9.1.2 Removing the XSCF Unit
    • 9.1.3 Installing the XSCF Unit
    • 9.1.4 Securing the Server
• Fan Modules Replacement
  • 10.1 Fan Module Replacement
    • 10.1.1 Accessing the 60-mm Fan Module
    • 10.1.2 Removing the 60-mm Fan Module
    • 10.1.3 Installing the 60-mm Fan Module
    • 10.1.4 Securing the Server
    • 10.1.5 Accessing the 172-mm Fan Module
    • 10.1.6 Removing the 172-mm Fan Module
    • 10.1.7 Installing the 172-mm Fan Module
    • 10.1.8 Securing the Server
    • 10.1.9 Accessing the 60-mm Fan Backplane
    • 10.1.10 Removing the 60-mm Fan Backplane
    • 10.1.11 Installing the 60-mm Fan Backplane
    • 10.1.12 Securing the Server
    • 10.1.13 Accessing the SPARC Enterprise M4000 172-mm Fan Backplane
    • 10.1.14 Removing the SPARC Enterprise M4000 172-mm Fan Backplane
    • 10.1.15 Installing the SPARC Enterprise M4000 172-mm Fan Backplane
    • 10.1.16 Securing the Server
    • 10.1.17 Accessing the SPARC Enterprise M5000 172-mm Fan Backplane
    • 10.1.18 Removing the SPARC Enterprise M5000 172-mm Fan Backplane
    • 10.1.19 Installing the SPARC Enterprise M5000 172-mm Fan Backplane
    • 10.1.20 Securing the Server
• Memory Board Replacement
  • 11.1 Memory Board Replacement
    • 11.1.1 Accessing the Memory Board
    • 11.1.2 Removing the Memory Board
    • 11.1.3 Installing the Memory Board
    • 11.1.4 Securing the Server
  • 11.2 DIMM Replacement
    • 11.2.1 Confirmation of DIMM Information
    • 11.2.2 Memory Installation Configuration Rules
    • 11.2.3 Installing Memory:
    • 11.2.4 Accessing the DIMMs
    • 11.2.5 Removing the DIMMs
    • 11.2.6 Installing the DIMMs
    • 11.2.7 Securing the Server
• CPU Module Replacement
  • 12.1 CPU Module Replacement
    • 12.1.1 Accessing the CPU Module
    • 12.1.2 Removing the CPU Module
    • 12.1.3 Installing the CPU Module
    • 12.1.4 Securing the Server
  • 12.2 CPU Upgrade
    • 12.2.1 SPARC64 VII CPU Modules Added to a New Domain
      • Adding a SPARC64 VII CPU Module to a New Domain
    • 12.2.2 SPARC64 VII Processors Added to an Existing Domain
      • Preparing to Add SPARC64 VII Processors to an Existing Domain
    • Adding a SPARC64 VII CPU Module to a Domain Configured With SPARC64 VI
    • Upgrading a SPARC64 VI CPU Module to SPARC64 VII on an Existing Domain
• Motherboard Unit Replacement
  • 13.1 Motherboard Unit Replacement
    • 13.1.1 Accessing the SPARC Enterprise M4000 Motherboard Unit
    • 13.1.2 Removing the SPARC Enterprise M4000 Motherboard Unit
    • 13.1.3 Installing the SPARC Enterprise M4000 Motherboard Unit
    • 13.1.4 Securing the Server
    • 13.1.5 Accessing the SPARC Enterprise M5000 Motherboard Unit
    • 13.1.6 Removing the SPARC Enterprise M5000 Motherboard Unit
    • 13.1.7 Installing the SPARC Enterprise M5000 Motherboard Unit
    • 13.1.8 Securing the Server
  • 13.2 DC-DC Converter Replacement
    • 13.2.1 Accessing the SPARC Enterprise M4000 DC-DC Converter
    • 13.2.2 Removing the SPARC Enterprise M4000 DC-DC Converter
    • 13.2.3 Installing the SPARC Enterprise M4000 DC-DC Converter
    • 13.2.4 Securing the Server
    • 13.2.5 Accessing the SPARC Enterprise M5000 DC-DC Converter
    • 13.2.6 Removing the SPARC Enterprise M5000 DC-DC Converter
    • 13.2.7 Installing the SPARC Enterprise M5000 DC-DC Converter
    • 13.2.8 Securing the Server
• Backplane Unit Replacement
  • 14.1 Backplane Unit Replacement
    • 14.1.1 Accessing the SPARC Enterprise M4000 Backplane Unit
    • 14.1.2 Removing the SPARC Enterprise M4000 Backplane Unit
    • 14.1.3 Installing the SPARC Enterprise M4000 Backplane Unit
    • 14.1.4 Securing the Server
    • 14.1.5 Accessing the SPARC Enterprise M5000 Backplane Unit
    • 14.1.6 Removing the SPARC Enterprise M5000 Backplane Unit
    • 14.1.7 Installing the SPARC Enterprise M5000 Backplane Unit
    • 14.1.8 Securing the Server
• Operator Panel Replacement
  • 15.1 Operator Panel Replacement
  • 15.2 Accessing the Operator Panel
    • 15.2.1 Removing the Operator Panel
    • 15.2.2 Installing the Operator Panel
    • 15.2.3 Securing the Server
• Components List
• Rules for System Configuration
  • B.1 Server Configuration
• FRU List
  • C.1 Server Overview
  • C.2 System Boards
    • C.2.1 Motherboard Unit
    • C.2.2 CPU Module
    • C.2.3 Memory Board
  • C.3 Backplane Unit
  • C.4 I/O Unit
  • C.5 Power
  • C.6 FAN Module
  • C.7 eXtended System Control Facility Unit
  • C.8 Drives
    • C.8.1 Hard Disk Drive
    • C.8.2 CD-RW/DVD-RW Drive Unit (DVDU)
    • C.8.3 Tape Drive Unit (TAPEU)
• External Interface Specifications
  • D.1 Serial Port
  • D.2 UPC (UPs Control) Port
  • D.3 USB Port
  • D.4 Connection Diagram for Serial Cable
• UPS Controller
  • E.1 Overview
  • E.2 Signal Cables
  • E.3 Signal Line Configuration
  • E.4 Power Supply Conditions
    • E.4.1 Input circuit
    • E.4.2 Output circuit
  • E.5 UPS Cable
  • E.6 UPC Connector
• Abbreviations
• Index