Alpha Technologies XM2, XM2-HV, XM2-HP - Manual (Page 84)

6.2 Intelligent CableUPS International Models
The following table shows the electrical, mechanical and physical specifications for the
International models of the Intelligent CableUPS.
XM2 Models: 906HP 906G5 608G5 910 915E 915M 915P 622CE 615CE HP 918HP
Electrical
Input Voltage (Vac):
120/240 115/230 115/230 120/240 190/220/247 100/112/127 190/220/253 230 230 120/240
Input Voltage Window: -30 to +20% -30 to +20% -30 to +20% -20 to +15% -20 to +15% -20 to +15% -20 to +15% -20 to +15% -20 to +15% -20 to +15%
Input Voltage Window w/ATS: n/a n/a n/a n/a -30 to +25% -30 to +25% -30 to +25% n/a n/a n/a
Input Frequency: 60Hz 50Hz 50Hz 60Hz 50Hz 60Hz 60Hz 50Hz 50Hz 60Hz
Input Frequency Window: ±3Hz ±3Hz ±3Hz ±3Hz ±3Hz ±3Hz ±3Hz ±3Hz ±3Hz ±3Hz
Output Voltage (Vac): 63/87 63/87 63 63/75/87 63/75/87 63/75/87 63/75/87 63/48 63/48 63/75/87
Output Current (A): 8/6 8/6 8 10/10/10 15/15/15 15/15/15 15/15/15 22/22 15/15 22/18/18
Max Output Power (VA): 540 540 540 900 1350 1350 1350 1350 900 1620
Output Waveform: Quasi-square wave
Voltage Regulation 1 : ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5%
Output
Frequency
Stability:
Line Mode 60Hz Nominal 50Hz Nominal 60Hz Nominal 50Hz Nominal 60Hz Nominal 50Hz Nominal 60Hz Nominal
Inverter Mode 60Hz, ±0.05% 50Hz, ±0.05% 60Hz, ±0.05% 50Hz, ±0.05% 60Hz, ±0.05% 50Hz, ±0.05% 60Hz, ±0.05%
Short Circuit Protection: <150% of maximum current rating
Transfer Characteristics: Uninterrupted output
Battery Voltage (Vdc): 36 36 36 36 36 36 36 48 36 36
Efficiency
(Typical Load Range)
Line Mode:
80-87% 86-90% 88-92%
Standby Mode: 79-84% 82-85% 84-86%
Battery Charger
Temperature Compensation:
Programmable (0 to 5mV/Cell/°C)
Charger Current: 10A at 80% load and nominal input (bulk charge mode)
Three Stage: Bulk, Accept, Float
Mechanical
Status Display:
2 x 20 Blue LCD with backlight
Dimensions H x W x D (in/mm): 8.8 x 15 x 13 / 222 x 381 x 330
Approx. Weight (lb/kg): 53/24 62/28.1 62/28.1 62/28.1 82/37.2 70/31.8 70/31.8 82/37.2 70/31.8 72/32.7
Finish: Black, epoxy powdercoat
Environment
Operating Temperature:
-40 to 55°C / -40 to 131°F
Relative Humidity: 0 to 95% non-condensing
Agency Compliance
FCC Part 15 Class A,
UL1778, UL1012,
CSA 22.2 No. 107.1:
Yes - - Yes - - - - - Yes
CE, EN50083-2, EN62040-2,
EN60950-1, EN62040-1:
- - Yes - - - - Yes Yes -
CB Scheme, IEC 60950-1, EMC
to CISPR22 Class A:
- Yes Yes - Yes 2 Yes Yes 3 - - -
Optional Features
Standard Protective Interface Module (PIM/N+1): Provides two programmable outputs from a single XM2 CableUPS power supply for redundancy in critical applications. The PIM
protects system components and provides isolation between distribution legs by shutting down the individual load during over-current conditions.
Five Output Protective Interface Module (PIM): Provides four programmable outputs from a single XM2 CableUPS power supply for protection in centralized powering applications. The PIM protects system components and
provides isolation between distribution legs by shutting down the individual load during over-current conditions. An Optical Network Unit (ONU) output is tied to Output 2.
Automatic Tap Switch (ATS): The ATS extends the input AC operating voltage range as indicated above. The ATS is used when a broader input operating range is needed due to utility voltage fluctuations and is currently
available in XM2-915 E/P/M models. Not used in the United States or Canada.
1 Note: Voltage regulation is maintained over both line and load ranges.
2 Note: Certified to CB Scheme and IEC 60950-1.
3 Note: Available only for XM2-915P-CB models.
Table 6-2 Specifications for International Models
84 017-805-B0-010 Rev. K2