Teledyne 6200E - Sulfides Analyzer User Manual
Page 175
Model 6200E Instruction Manual
Calibration Procedures
M6200E Rev: A1
175
Toggle keys
to set
number of
days
between
procedures
(1-367)
Toggle keys
to set
delay time for
each iteration
of the
sequence:
HH:MM
(0 – 24:00)
SETUP X.X
DELTA D AYS: 1
<SET SET>
EDIT
EXIT
SETUP X.X
DELTA DAYS: 1
0 0 2
ENTR
EXIT
SETUP X.X
DELTA DAYS:2
<SET
SET>
EDIT
EXIT
SETUP X.X
DELTA TIM E00:00
<SET SET>
EDIT
EXIT
SETUP X.X
DELTA TIME: 00:00
0 0 :3 0
ENTR
EXIT
SETUP X.X
DELTA TIEM:00:30
<SET
SET>
EDIT
EXIT
SETUP X.X
STARTING TIM E:14:15
<SET
SET>
EDIT
EXIT
EXIT returns
to the SETUP
Menu
SETUP X.X
DURATION:15.0 M INUTES
<SET SET>
EDIT
EXIT
SETUP X.X
DURATION 15.0MINUTES
3 0 .0
ENTR
EXIT
SETUP X.X
DURATION:30.0 M INUTES
<SET
SET>
EDIT
EXIT
Toggle keys
to set
duration for
each
iteration of
the
sequence:
Set in
Decimal
minutes
from
0.1 – 60.0
SETUP X.X
CALIBRATE: OFF
<SET SET>
EDIT
EXIT
SETUP X.X C ALIBRAT E: OFF
ON
ENTR
EXIT
SETUP X.X
CALIBRATE: ON
<SET SET> EDIT
EXIT
Toggle key
between
Off and
ON
SETUP X.X
SEQ 2) ZERO–SPAN, 2:00:30
PREV NEXT
MODE
SET
EXIT
Sequence
Delta Time
MODE Delta Days
SAMPLE
ENTER SETUP PASS : 818
8 1 8
ENTR
EXIT
SETUP X.X
PRIMARY SETUP MENU
CFG
AC AL
DAS RNGE PASS CLK MORE EXIT
SETUP X.X
SEQ 1) DISABLED
NEXT
MODE
EXIT
SETUP X.X
SEQ 2) DISABLED
PREV NEXT
M ODE
EXIT
SETUP X.X
M ODE: DISABLED
NEXT
ENTR EXIT
SETUP X.X
MODE: ZERO
PREV
NEXT
ENTR EXIT
SETUP X.X
M ODE: ZERO–SPAN
PREV
NEXT
ENTR
EXIT
SETUP X.X
SEQ 2) ZERO–SPAN, 1:00:00
PREV NEXT
MODE
SET
EXIT
SETUP X.X
TIM ER ENABLE: ON
SET>
EDIT
EXIT
SETUP X.X
STARTING DATE: 01–JAN–02
<SET SET>
EDIT
EXIT
SETUP X.X
STARTING DATE: 01–JAN–02
0
4 SEP
0
3
ENTR
EXIT
Toggle keys
to set
day, m onth &
year:
Form at :
DD-MON-Y
Y
SETUP X.X
STARTING DATE: 04–SEP–03
<SET
SET>
EDIT
EXIT
Default
value is
ON
SETUP X.X
STARTING DATE: 04–SEP–03
<SET
SET>
EDIT
EXIT
SETUP X.X
STARTING TIM E:00:00
<SET SET>
EDIT
EXIT
SETUP X.X
STARTING TIM E:00:00
1 4 : 1 5
ENTR
EXIT/
Toggle keys to
set time:
Format : HH:MM
This is a 24 hr
clock .
PM hours are
13 – 24.
Example
2:15 PM = 14:15
SAMPLE RANGE = 500.0 PPB
H2S
=XXX.X
< TST TST > CAL CALZ CALS
SETUP
With dynamic calibration turned on, the state of the internal setup variables DYN_SPAN and
DYN_ZERO is set to ON and the instrument will reset the slope and offset values for the H
2
S
response each time the AutoCal program runs. This continuous re-adjustment of calibration
parameters can often mask subtle fault conditions in the analyzer. It is recommended that, if
dynamic calibration is enabled, the analyzer’s test functions, slope and offset values be checked
frequently to assure high quality and accurate data from the instrument.