Document Outline

• Contents
• 1. Introduction
  •  Regarding This Manual
  • 1.1 Safe Use of This Product
  • 1.2 Warranty
  • 1.3 ATEX Documentation
• 2. Handling Cautions
  • 2.1 Model and Specifications Check
  • 2.2 Unpacking
  • 2.3 Storage
  • 2.4 Selecting the Installation Location
  • 2.5 Waterproofing of Cable Conduit Connections
  • 2.6 Restrictions on Use of Radio Transceivers
  • 2.7 Insulation Resistance and Dielectric Strength Test
  • 2.8 Installation of an Explosion-Protected Instrument
    • 2.8.1 FM approval
    • 2.8.2 CSA Certification
    • 2.8.3 CENELEC ATEX Certification
    • 2.8.4 IECEx Certification
• 3. Component Names
• 4. About Fieldbus
  • 4.1 Outline
  • 4.2 Internal Structure of FVX110
    • 4.2.1 System/network Management VFD
    • 4.2.2 Function Block VFD
  • 4.3 Logical Structure of Each Block
  • 4.4 Wiring System Configuration
• 5. Installation
  • 5.1 Precautions
  • 5.2 Mounting
  • 5.3 Wiring
    • 5.3.1 Wiring Precautions
    • 5.3.2 Wiring Installation
  • 5.4 Grounding
  • 5.5 Connection of Devices
  • 5.6 Host Setting
  • 5.7 Bus Power ON
  • 5.8 Integration of DD
  • 5.9 Set the Parameters Using DTM
  • 5.10 Continuous Record of Values
  • 5.11 Generation of Alarm
• 6. Configuration
  • 6.1 Network Design
  • 6.2 Network Definition
  • 6.3 Definition of Combining Function Blocks
  • 6.4 Setting of Tags and Addresses
  • 6.5 Communication Setting
    • 6.5.1 VCR Setting
    • 6.5.2 Function Block Execution Control
  • 6.6 Block Setting
    • 6.6.1 Link Object
    • 6.6.2 Trend Object
    • 6.6.3 View Object
    • 6.6.4 Function Block Parameters
• 7. Explanation of Basic Items
  • 7.1 Outline
  • 7.2 Setting and Changing Parameters for the Whole Process
  • 7.3 LCD Transducer Block
    • 7.3.1 Function Outline
    • 7.3.2 Operating mode
    • 7.3.3 Indicator names and functions
    • 7.3.4 Communication status indication
    • 7.3.5 Indicator settings
    • 7.3.6 Other display settings
    • 7.3.7 Flow chart of indicator settings
    • 7.3.8 Units the auto link function allows you to display on the LCD
• 8. Explanation of Basic Items (switching displays)
  • 8.1 Single Scroll Mode
  • 8.2 Continuous Scroll Mode (scan mode)
  • 8.3 Direction of Display Switching
• 9. In-Process Operation
  • 9.1 Mode Transition
  • 9.2 Generation of Alarm
    • 9.2.1 Indication of Alarm
    • 9.2.2 Alarms and Events
    • 9.2.3 Standard categories for NAMUR NE-107 instrument diagnostics alarms
  • 9.3 Device Diagnostic Simulation Function
  • 9.4 Write lock (Write-protect) function
• 10. Maintenance
  • 10.1 Overview
  • 10.2 Disassembly and Reassembly
    • 10.2.1 Replacing the display
    • 10.2.2 Replacing the CPU Board Assembly
• 11. Device Information
  • 11.1 DEVICE STATUS
  • 11.2 Status of Each Parameter in Failure Mode
• 12. Parameter Lists
  • 12.1 Resource Block
  • 12.2 LCD Transducer Block
• 13. General Specifications
  • 13.1 Functional Specifications
  • 13.2 Physical Specifications
  • 13.3 Model and Suffix Codes
  • 13.4 Optional Specifications (For Explosion Protected type)
  • 13.5 Optional Specifications
  • 13.6 Dimensions
• Appendix 1. Signal Characterizer (SC) Block
  • A1.1 Schematic Diagram of Signal Characterizer Block
  • A1.2 Input Section
    • A1.2.1 Determining the Mode
    • A1.2.2 Judging BLOCK_ERR
  • A1.3 Line-segment Factor Determination Section
    • A1.3.1 Conditions for Configuring Valid Coefficients (CURVE_X, CURVE_Y)
  • A1.4 List of Signal Characterizer Block Parameters
  • A1.5 Application Example
    • A1.5.1 Input Compensation
    • A1.5.2 Calorie Flow Compensation
    • A1.5.3 Backward Control
• Appendix 2. Integrator (IT) Block
  • A2.1 Schematic Diagram of Integrator Block
  • A2.2 Input Process Section
    • A2.2.1 Determining Input Value Statuses
    • A2.2.2 Converting the Rate
    • A2.2.3 Converting Accumulation
    • A2.2.4 Determining the Input Flow Direction
  • A2.3 Adder
    • A2.3.1 Status of Value after Addition
    • A2.3.2 Addition
  • A2.4 Integrator
  • A2.5 Output Process
    • A2.5.1 Status Determination
    • A2.5.2 Determining the Output Value
    • A2.5.3 Mode Handling
  • A2.6 Reset
    • A2.6.1 Reset Trigger
    • A2.6.2 Reset Timing
    • A2.6.3 Reset Process
  • A2.7 List of Integrator Block Parameters
• Appendix 3. Input Selector (IS) Block
  • A3.1 Input Selector Function Block Schematic
  • A3.2 Input Section
    • A3.2.1 Mode Handling
    • A3.2.2 MIN_GOOD Handling
  • A3.3 Selection
    • A3.3.1 OP_SELECT Handling
    • A3.3.2 SELECTION Handling
  • A3.4 Output Processing
    • A3.4.1 Handling of SELECTED
    • A3.4.2 OUT Processing
    • A3.4.3 STATUS_OPTS
  • A3.5 List of Input Selector Block Parameters
  • A3.6 Application Example
• Appendix 4. Arithmetic (AR) Block
  • A4.1 Arithmetic Function Block Schematic
  • A4.2 Input Section
    • A4.2.1 Main Inputs
    • A4.2.2 Auxiliary Inputs
    • A4.2.3 INPUT_OPTS
    • A4.2.4 Relationship between the Main Inputs and PV
  • A4.3 Computation Section
    • A4.3.1 Computing Equations
    • A4.3.2 Compensated Values
    • A4.3.3 Average Calculation
  • A4.4 Output Section
    • A4.4.1 Mode Handling
    • A4.4.2 Status Handling
  • A4.5 List of the Arithmetic Block Parameters
• Appendix 5. PID Block
  • A5.1 Function Diagram
  • A5.2 Functions of PID Block
  • A5.3 Parameters of PID Block
  • A5.4 PID Computation Details
    • A5.4.1 PV-proportional and -derivative Type PID (I-PD) Control Algorithm
    • A5.4.2 PID Control Parameters
  • A5.5 Control Output
    • A5.5.1 Velocity Type Output Action
  • A5.6 Direction of Control Action
  • A5.7 Control Action Bypass
  • A5.8 Feed-forward
  • A5.9 Block Modes
    • A5.9.1 Mode Transitions
  • A5.10 Bumpless Transfer
  • A5.11 Setpoint Limiters
    • A5.11.1 When PID Block Is in Auto Mode
    • A5.11.2 When PID Block Is in Cas or RCas Mode
  • A5.12 External-output Tracking
  • A5.13 Measured-value Tracking
  • A5.14 Initialization and Manual Fallback (IMan)
  • A5.15 Manual Fallback
  • A5.16 Auto Fallback
  • A5.17 Mode Shedding upon Computer Failure
    • A5.17.1 SHED_OPT
  • A5.18 Alarms
    • A5.18.1 Block Alarm (BLOCK_ALM)
    • A5.18.2 Process Alarms
  • A5.19 Example of Block Connections
  • A5.20 View Object for PID Function Block
• Appendix 6. Multiple Analog Output (MAO) Block
  • A6.1 Function Block Diagram
  • A6.2 Block Mode
  • A6.3 Fault State
    • A6.3.1 Transition to Fault State
    • A6.3.2 Clearing a Fault State
    • A6.3.3 Fault State Operation
  • A6.4 Status Transitions
  • A6.5 Parameter list display
• Appendix 7. Link Master Functions
  • A7.1 Link Active Scheduler
  • A7.2 Link Master
  • A7.3 Transfer of LAS
  • A7.4 LM Functions
  • A7.5 LM Parameters
    • A7.5.1 LM Parameter List
    • A7.5.2 Descriptions for LM Parameters
  • A7.6 FAQs
• Appendix 8. Software Download
  • A8.1 Benefits of Software Download
  • A8.2 Specifications
  • A8.3 Preparations for Software Downloading
  • A8.4 Software Download Sequence
  • A8.5 Download Files
  • A8.6 Steps after Activating a Field Device
  • A8.7 Troubleshooting
  • A8.8 Resource Block’s Parameters Relating to Software Download
  • A8.9 System/Network Management VFD Parameters Relating to Software Download
  • A8.10 Comments on System/Network Management VFD Parameters Relating to Software Download
• Revision Information