Campbell Scientific LoggerNet Datalogger Support Software - Manual (Page 551)

Appendix E. Log Files
Communications Status Log Example
"2009-04-15 16:41:05.367","IPPort","S","Device dialed"
"2009-04-15 16:41:05.382","PakBusPort_ip","S","sending message","src: 4094","dest: 2","proto: PakCtrl","type: 0x09","tran: 214"
"2009-04-15 16:41:05.398","PakBusPort_ip","S","received message","src: 2","dest: 4094","proto: PakCtrl","type: 0x89","tran: 214"
"2009-04-15 16:41:05.398","CR1000","S","PakCtrl message received","89"
"2009-04-15 16:41:05.413","PakBusPort_ip","S","sending message","src: 4094","dest: 2","proto: BMP5","type: 0x17","tran: 213"
"2009-04-15 16:41:05.429","PakBusPort_ip","S","received message","src: 2","dest: 4094","proto: BMP5","type: 0x97","tran: 213"
"2009-04-15 16:41:05.429","CR1000","S","BMP5 message received","type: 0x97","check/set clock"
"2009-04-15 16:41:06.367","PakBusPort_ip","S","sending message","src: 4094","dest: 2","proto: BMP5","type: 0x09","tran: 217"
"2009-04-15 16:41:06.382","PakBusPort_ip","S","received message","src: 2","dest: 4094","proto: BMP5","type: 0x89","tran: 217"
"2009-04-15 16:41:06.382","CR1000","S","BMP5 message received","type: 0x89","table poll","CR1000.TestFast"
"2009-04-15 16:41:06.382","PakBusPort_ip","S","sending message","src: 4094","dest: 2","proto: BMP5","type: 0x09","tran: 218"
"2009-04-15 16:41:06.492","PakBusPort_ip","S","received message","src: 2","dest: 4094","proto: BMP5","type: 0x89","tran: 218"
"2009-04-15 16:41:06.492","CR1000","S","BMP5 message received","type: 0x89","table poll","CR1000.TestFast"
"2009-04-15 16:41:06.523","PakBusPort_ip","S","sending message","src: 4094","dest: 2","proto: BMP5","type: 0x17","tran: 219"
"2009-04-15 16:41:06.523","PakBusPort_ip","S","received message","src: 2","dest: 4094","proto: BMP5","type: 0x97","tran: 219"
TABLE E-2. Communication Status Log Messages
Message Text Message Meaning User Response to Message
Serial packet X exchanged The low level serial
BMP1 communication
framing packet was sent
and the response
received from the device.
(CR10X-TD table based
type devices)
Classic;;Cmd The listed command was
sent to an array based
datalogger.
For a list of the commands and their
meanings see the datalogger
operator’s manual.
BMP1 packet received A BMP1 packet was
received from the device.
(CR10X-TD type
devices only)
RPC packet exchanged A BMP3 packet was
exchanged. (CR5000,
CR9000 dataloggers
only)
Datalogger did not respond to
end command
The computer tried to
terminate the connection
but the datalogger did
not acknowledge the
shutdown.
This is an indication that there is a
communications problem between
the computer and the datalogger.
Check the cables and connectors
and make sure the datalogger has
power.
E-19