Commissioning – Lenze ESV SMV frequency inverter User Manual
Page 50
48
Lenze SMVector 13465100 EDBSV01 EN v18
Commissioning
Code
Possible Settings
IMPORTANT
No.
Name
Default Selection
P708
Sequencer: Time
units/scaling
0
0 0.1
{sec}
6553.5
Setup units/scaling for all sequencer time
related parameters
1 1
{sec}
65535
2 1
{min}
65535
NOTE:
P708 rescales the following sequencer related parameters:
- Segment Times in current step: P712, P717, P722, P727, P732, P737, P742, P747,
P752, P757, P762, P767, P772, P777, P782, P787, P792
- Sequence diagnostic/status: P561, P562
Segment #1
P710
Segment #1
Frequency Setpoint
0.0
-500.0 {Hz} 500.0
If P112 = 1, negative sign forces reverse
direction
P711
Segment #1
Accel/Decel Time
20.0
0.0
{sec} 3600.0
P712
Segment #1
Time in current step
0.0
0
0.0
{P708} 6553.5
0
{P708} 65535
Scaling/units depend on P708
Skip segment if time = 0
P713
Segment #1
Digital Output State
0
Value set in P713
0 1 2 3 4 5 6 7
Relay (Bit 0)
0 1 0 1 0 1 0 1
TB14 (Bit 1)
0 0 1 1 0 0 1 1
I/O option Relay (Bit 2)
0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27
P714
Segment #1 TB30
Analog Output
Value
0.00
0.00
{VDC} 10.00
TB30 configuration parameter must be set to
accept this value: P150 = 10
Segment #2
P715
Segment #2
Frequency Setpoint
0.0
-500.0 {Hz} 500.0
If P112 = 1, negative sign forces reverse
direction
P716
Segment #2
Accel/Decel Time
20.0
0.0
{sec} 3600.0
P717
Segment #2
Time in current step
0.0
0
0.0
{P708} 6553.5
0
{P708} 65535
Scaling/units depend on P708
Skip segment if time = 0
P718
Segment #2
Digital Output State
0
Value set in P718
0 1 2 3 4 5 6 7
Relay (Bit 0)
0 1 0 1 0 1 0 1
TB14 (Bit 1)
0 0 1 1 0 0 1 1
I/O option Relay (Bit 2)
0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27
P719
Segment #2 TB30
Analog Output
Value
0.00
0.00
{VDC} 10.00
TB30 configuration parameter must be set to
accept this value: P150 = 10