Document Outline

• IASIMP-QS001C-EN-P, CompactLogix System Quick Start
• Table of Contents
  • About This Publication
  • Required Software
  • Parts List
  • Conventions
  • Additional Resources
• 1-Prepare the CompactLogix Hardware
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Connect the Battery to the Controller
  • Record the Ethernet Address (MAC)
  • Set the ControlNet Node Address
  • Assemble the System
  • Make Network Connections
  • Wire Power
  • Additional Resources
• 2-Prepare the Computer
  • Before You Begin
  • What You Need
  • Terminology
  • Make Network Connections
  • Install RSLogix Programming Software
  • Configure a Serial Driver
  • Set the IP Address for the Computer
  • Configure the EtherNet/IP Driver in RSLinx Software
  • Load Firmware
  • Install Additional Software
  • Additional Resources
• 3-Prepare the Distributed POINT I/O Hardware
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Mount and Connect the Network Adapter
  • Mount the POINT I/O Modules
  • Mount and Wire the POINT I/O Power Supply
  • Wire the Adapter and I/O Modules to the Power Supply
  • Additional Resources
• 4-Prepare the PowerFlex 70 Drive
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Mount the PowerFlex 70 Drive
  • Wire Power
  • Configure the Communication Adapter
  • Connect Communication Adapter to the PowerFlex 70 Drive
  • Additional Resources
• 5-Prepare the PowerFlex 40 Drive
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Mount the PowerFlex 40 Drive
  • Wire Power
  • Configure the Communication Adapter
  • Connect the Communication Adapter to the PowerFlex 40 Drive
  • Additional Resources
• 6-Prepare the PanelView Plus Terminal
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Install the ControlNet Interface Module
  • Mount the PanelView Plus Terminal
  • Wire the PanelView Plus Terminal to the Power Supply
  • Make Network Connections
  • Assign an IP Address
  • Additional Resources
• 7-Configure the EtherNet/IP Network
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Terminology
  • Assign IP Addresses to Devices
  • Browse the EtherNet/IP Network in RSLinx
  • Additional Resources
• 8-Configure the ControlNet Driver
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Configure the ControlNet Driver in RSLinx
  • Additional Resources
• 9-Configure the DeviceNet Network
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Apply Power to the DeviceNet Network
  • Set the 1769-SDN Module’s Node Address
  • Create a DeviceNet Configuration File
  • Additional Resources
• 10-Create a Project Using RSLogix 5000 Programming Software
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Create a Project
  • Configure the Controller
  • Add Local I/O Modules
  • Add Ladder Logic to Test the Local 1769 Compact I/O Modules
  • Set the Communication Path and Download to the Controller
  • Add the 1769-SDN to the Project
  • Additional Resources
• 11-Add Distributed I/O Modules to the Project
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Add Distributed I/O Modules
  • Edit the DeviceNet Adapter Parameters
  • Configure the DeviceNet Subnet
  • Create a DeviceNet Scanlist
  • Add Ladder Logic
  • Create DeviceNet Tags and Add Ladder Logic
  • Download the Project
  • Set the POINT I/O Chassis Size
  • Schedule the ControlNet Network
  • Test the Distributed I/O Light
  • Additional Resources
• 12-Create a PowerFlex 70 Application
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Add the Drive to Your RSLogix 5000 Project and Connect to the Drive
  • Edit the Drive Parameters
  • Create a DeviceNet Scanlist
  • Create DeviceNet Tags
  • Download the Project
  • Schedule the ControlNet Network
  • Test the PowerFlex 70 Tags
  • Test the PowerFlex 70 Tags
  • Additional Resources
• 13-Create a PowerFlex 40 Application
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Add the Drive to Your RSLogix 5000 Project
  • Create a DeviceNet Scanlist
  • Create DeviceNet Tags
  • Download the Project
  • Schedule the ControlNet Network
  • Edit PowerFlex 40 Parameter Values
  • Test the PowerFlex 40 Tags
  • Test the PowerFlex 40 Tags
  • Additional Resources
• 14-Create a PanelView Plus Application
  • Before You Begin
  • What You Need
  • Follow These Steps
  • Create a New Application
  • Create an RSLinx Enterprise Configuration in FactoryTalkView ME
  • Create Device Shortcuts to the Controller
  • Create the OB16_Light Indicator
  • Create a Push Button
  • Test the Indicator and Push Button
  • Add a Goto Configuration Mode Button
  • Assign Keys
  • Assign an Initial Screen
  • Transfer to PanelView Plus Firmware
  • Test the Application on the PanelView Plus Application
  • Additional Resources
• Network Worksheet
  • EtherNet/IP
  • DeviceNet Network
  • 1769-SDN Module Information
  • RSNetWorx DeviceNet Configuration File Information
  • ControlNet Network
• Back Cover