Teac SS-CDR200 - Manual (Page 30)

30
TASCAM SS-CDR200/SS-R200/SS-R100
In this manual, unless otherwise specified, explanations
assume that the playback mode is set to
CONTINUE
(continuous playback mode).
Selecting tracks
To select a track for playback, if the play area has more
than one track, you can either skip to the previous or next
track or enter a track number directly. Both methods are
explained below.
Skipping to the previous or next track
Turn the MULTI JOG dial (or press the remote control
SKIP . and / buttons) to skip to the previous or
next track.
• Turn the MULTI JOG dial right to skip to the next track
or to the left to skip to the previous track.
• Press the remote control SKIP / button to skip to
the next track or . button to skip to the previous
track.
After selecting the track, press the front panel or remote
control PLAY button to start track playback.
Alternatively, instead of pressing the front panel or
remote control PLAY button, press the front panel or
remote control READY button to start playback standby
at the beginning of the selected track.
Specifying a track number
You can use the remote’s number buttons to directly enter
the number of the track that you want to play.
For audio format CDs, the track number will be a
maximum of two digits. For MP3 and WAV format media,
the track number will be a maximum of three digits.
1 Use the remote’s number buttons to input the track
number. Enter the track number starting with the
highest digit.
Example 1: For track 1, press 1
Example 2: For track 12, press 1 followed by 2
Example 3: For track 103 press 1 followed by 0 and
then 3
2 Press the front panel or remote control PLAY
button to start playback of the selected track.
Alternatively, instead of pressing the front panel or
remote control PLAY button, press the front panel
or remote control READY button to start playback
standby at the beginning of the selected track.
NOTE
• Instead of pressing the front panel or remote control
PLAY button, you can also press the MULTI JOG dial or
remote control ENTER button to start playback of the
selected track.
• You cannot use the number buttons on the remote to
specify the track while in program or random mode.
Searching backward and forward
You can search forward or backward in a track while
listening to the audio.
1 Play the desired track or put it into playback
standby.
2 Press and hold the m [SKIP] or , [LOCK]
button (or remote control SEARCH m or ,
button) to start searching backward or forward.
3 To stop searching, release the button you are
holding.
The unit will return to the state (playback standby or
playback) it was in before searching.
Time search
When the unit is stopped, in playback standby or playing,
you can locate to a specified time in the specified track.
NOTE
You cannot use time search when the play mode is
PROGRAM
or
RANDOM
.
Use the remote control number buttons to input numbers
in the following order.
• Track number: 3 digits
• Elapsed time from the beginning of the track: two
digits each hours, minutes, seconds
For example, if you want to specify a location that is 1
minute 30 seconds from the beginning of track 2, you
would press keys in the following order.
0 q 0 q 2 q 0 q 0 q 0 q 1 q 3 q 0
When you finish entering the nine digits, the unit will
automatically locate to the specified position.
If the unit was stopped or playing back before locating to
the time, playback will begin after locating. If the unit was
in playback standby prior to locating to the time, it will
resume playback standby after locating.
If you specify a track number that does not exist in the
current play area or a time that does not exist in the track,
the operation will be cancelled at that point.
Time searching after partial entry
If you press the remote’s ENTER, PLAY or READY button
before you finish entering the time, you will locate to the
position that is specified at that point.
For example, suppose you intend to specify a location
that is 12 minutes from the beginning of track 2, but do
not complete the entry, inputting only:
0 q 0 q 2 q 0 q 0 q 1 q 2
Then, if you press the remote control ENTER, PLAY or
READY button, the unit will locate to 12 minutes after the
beginning of track 2. The button you push will determine
what happens after locating.
4 − Preparations