Verilink QUAD/IMUX (880-502392-001) Product Manual - Manual (Page 29)

Quick Set-Up
Verilink QUAD/IMUX User Manual
2-11
23. Use the “I1”, “I2”, “I3”, and “I4” commands to set the Clear
Interval to 30 seconds. Now, if a T1 fails, the IMUX 2160 will
stop using that T1 (as it always does) and only resume using it
when the T1 failure has been resolved for 30 seconds. Type
“X” twice to return to the Main Menu for the QUAD 2164.
24. Repeat Step 19 through Step 23 for the two remaining QUAD
2164 modules in slots 7 and 8.
Configure the
IMUX 2160s
1. From the Main Menu use the “S” command to navigate to slot 4
where the first IMUX 2160 resides. Use the “C” command to
access the IMUX 2160 Configuration Menu.
Figure 2-10 IMUX 2160 Configuration Menu
2. The Line Type Line Type Line Type Line Type of T1 is correct for this example. 64K is the
correct setting for Channel Rate Channel Rate Channel Rate Channel Rate when a B8ZS T1 is used.
NOTE: When Rx Clock Rx Clock Rx Clock Rx Clock is set to “INVERT” the clock signal is actually
normal. When Rx Clock Rx Clock Rx Clock Rx Clock is set to “NORMAL” the clock signal is
actually inverted. When Tx Clock Tx Clock Tx Clock Tx Clock is set to “INVERT” the clock
signal is actually normal. When Tx Clock Tx Clock Tx Clock Tx Clock is set to “NORMAL”
the clock is actually inverted.
-- IMUX 2160 CONFIGURATION MENU -- -- IMUX 2160 CONFIGURATION MENU -- -- IMUX 2160 CONFIGURATION MENU -- -- IMUX 2160 CONFIGURATION MENU --
FW Rev : 1.28 FW Rev : 1.28 FW Rev : 1.28 FW Rev : 1.28
L) Line Type : T1 DSR) NO
L) Line Type : T1 DSR) NO L) Line Type : T1 DSR) NO L) Line Type : T1 DSR) NO
C) Channel Rate: 64K CTS) NO
C) Channel Rate: 64K CTS) NO C) Channel Rate: 64K CTS) NO C) Channel Rate: 64K CTS) NO
R) Rx Clk Phase: INVERT DCD) YES
R) Rx Clk Phase: INVERT DCD) YES R) Rx Clk Phase: INVERT DCD) YES R) Rx Clk Phase: INVERT DCD) YES
T) Tx Clk Phase: INVERT TM) NO
T) Tx Clk Phase: INVERT TM) NO T) Tx Clk Phase: INVERT TM) NO T) Tx Clk Phase: INVERT TM) NO
F) Ref Clk Phase: NORMAL
F) Ref Clk Phase: NORMAL F) Ref Clk Phase: NORMAL F) Ref Clk Phase: NORMAL
H) DTE Handshake: AUTOMATIC
H) DTE Handshake: AUTOMATIC H) DTE Handshake: AUTOMATIC H) DTE Handshake: AUTOMATIC
DTE Type: V.35
DTE Type: V.35 DTE Type: V.35 DTE Type: V.35
Q1) Quad Card 1:
Q1) Quad Card 1: Q1) Quad Card 1: Q1) Quad Card 1:
Q2) Quad Card 2:
Q2) Quad Card 2: Q2) Quad Card 2: Q2) Quad Card 2:
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Lines Equipped:
Lines Equipped: Lines Equipped: Lines Equipped:
Lines Active:
Lines Active: Lines Active: Lines Active:
Frame Sync:
Frame Sync: Frame Sync: Frame Sync:
CTS Received:
CTS Received: CTS Received: CTS Received:
CRC Error:
CRC Error: CRC Error: CRC Error:
Far CRC Error:
Far CRC Error: Far CRC Error: Far CRC Error:
X) main menu X) main menu X) main menu X) main menu
A [0.0.0.206] [1,4] IMUX 2160 > A [0.0.0.206] [1,4] IMUX 2160 > A [0.0.0.206] [1,4] IMUX 2160 > A [0.0.0.206] [1,4] IMUX 2160 >