Verilink QUAD/IMUX (880-502392-001) Product Manual - Manual (Page 40)

E1 Configuration Menus
3-2
Verilink QUAD/IMUX User Manual
Figure 3-1 Quad 2164 Main Menu
Table 3-1 Main Menu Commands
Shelf/Slot
Selection
To select a shelf and slot to manage, type “S” and press E NTER . Type
the shelf number of the desired module and press E NTER . Type the
slot number and press E NTER again. The screen updates to display
the selected shelf and slot in [ ] brackets. In Figure 3-1 the QUAD
2164 module in shelf 1, slot 1 is the selected card.
-- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 -- -- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 -- -- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 -- -- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 --
Site Name: Site Name: Site Name: Site Name:
Access level: 4
Access level: 4 Access level: 4 Access level: 4
<- SLOT ->
<- SLOT -> <- SLOT -> <- SLOT ->
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13 SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13 SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
0 - - - - - - - - - - - - -
0 - - - - - - - - - - - - - 0 - - - - - - - - - - - - - 0 - - - - - - - - - - - - -
1 D [*Q] M
1 D [*Q] M 1 D [*Q] M 1 D [*Q] M
2 - - - - - - - - - - - - -
2 - - - - - - - - - - - - - 2 - - - - - - - - - - - - - 2 - - - - - - - - - - - - -
3 - - - - - - - - - - - - -
3 - - - - - - - - - - - - - 3 - - - - - - - - - - - - - 3 - - - - - - - - - - - - -
4 - - - - - - - - - - - - -
4 - - - - - - - - - - - - - 4 - - - - - - - - - - - - - 4 - - - - - - - - - - - - -
5 - - - - - - - - - - - - -
5 - - - - - - - - - - - - - 5 - - - - - - - - - - - - - 5 - - - - - - - - - - - - -
6 - - - - - - - - - - - - -
6 - - - - - - - - - - - - - 6 - - - - - - - - - - - - - 6 - - - - - - - - - - - - -
7 - - - - - - - - - - - - -
7 - - - - - - - - - - - - - 7 - - - - - - - - - - - - - 7 - - - - - - - - - - - - -
8 - - - - - - - - - - - - -
8 - - - - - - - - - - - - - 8 - - - - - - - - - - - - - 8 - - - - - - - - - - - - -
KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI
KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI
S) shelf/slot O) node administration S) shelf/slot O) node administration S) shelf/slot O) node administration S) shelf/slot O) node administration
M) enable alarm monitor A) display alarm buffer
M) enable alarm monitor A) display alarm buffer M) enable alarm monitor A) display alarm buffer M) enable alarm monitor A) display alarm buffer
C) configuration D) diagnostics
C) configuration D) diagnostics C) configuration D) diagnostics C) configuration D) diagnostics
P) performance/status B) circuit
P) performance/status B) circuit P) performance/status B) circuit P) performance/status B) circuit
X) system log off
X) system log off X) system log off X) system log off
[1,1] QUAD 2164 > [1,1] QUAD 2164 > [1,1] QUAD 2164 > [1,1] QUAD 2164 >
Command Description
S Shelf/slot—See Shelf/Slot Selection in this chapter.
M Enable Alarm Monitor—See Chapter 5, " Performance Monitoring ".
C Configuration—See E1 QUAD Configuration Menu in this chapter.
P Performance/status—See Chapter 5, " Performance Monitoring ".
O Node Administration—See E1 Node Administration , in this chapter.
A Display Alarm Buffer—See Chapter 5, " Performance Monitoring ".
D Diagnostics—See Chapter 6, " Diagnostics ".
B Circuit—Not supported by the QUAD/IMUX product.
X System Log Off