Verilink QUAD/IMUX (880-502392-001) Product Manual - Manual (Page 32)

Quick Set-Up
2-14
Verilink QUAD/IMUX User Manual
Figure 2-11 QUAD 2164 Main Menu
WARNING Never configure any SLIP IP address through the
Craft interface of a QUAD 2164 module (firmware versions
4.30 or lower). There is no RS-232 interface for use with
SLIP—and the module WILL fail, requiring factory repair, if
the SLIP address conflicts with the Ethernet address.
3. Type “C” to access the QUAD 2164 Configuration Menu.
-- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 -- -- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 -- -- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 -- -- VERILINK ACE CONTROLLER at [1,1]: FW Rev 4.30, Oct 12 1998 --
Site Name: Site Name: Site Name: Site Name:
Access level: 4
Access level: 4 Access level: 4 Access level: 4
<- SLOT ->
<- SLOT -> <- SLOT -> <- SLOT ->
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13 SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13 SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
0 - - - - - - - - - - - - -
0 - - - - - - - - - - - - - 0 - - - - - - - - - - - - - 0 - - - - - - - - - - - - -
1 D [Q] M
1 D [Q] M 1 D [Q] M 1 D [Q] M
2 - - - - - - - - - - - - -
2 - - - - - - - - - - - - - 2 - - - - - - - - - - - - - 2 - - - - - - - - - - - - -
3 - - - - - - - - - - - - -
3 - - - - - - - - - - - - - 3 - - - - - - - - - - - - - 3 - - - - - - - - - - - - -
4 - - - - - - - - - - - - -
4 - - - - - - - - - - - - - 4 - - - - - - - - - - - - - 4 - - - - - - - - - - - - -
5 - - - - - - - - - - - - -
5 - - - - - - - - - - - - - 5 - - - - - - - - - - - - - 5 - - - - - - - - - - - - -
6 - - - - - - - - - - - - -
6 - - - - - - - - - - - - - 6 - - - - - - - - - - - - - 6 - - - - - - - - - - - - -
7 - - - - - - - - - - - - -
7 - - - - - - - - - - - - - 7 - - - - - - - - - - - - - 7 - - - - - - - - - - - - -
8 - - - - - - - - - - - - -
8 - - - - - - - - - - - - - 8 - - - - - - - - - - - - - 8 - - - - - - - - - - - - -
KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI
KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI KEY: *=CONTROLLER N=NCM Q=QUAD M=IMUX A=DIDCSU U=DCSU P=DPRI
S) shelf/slot O) node administration S) shelf/slot O) node administration S) shelf/slot O) node administration S) shelf/slot O) node administration
M) enable alarm monitor A) display alarm buffer
M) enable alarm monitor A) display alarm buffer M) enable alarm monitor A) display alarm buffer M) enable alarm monitor A) display alarm buffer
C) configuration D) diagnostics
C) configuration D) diagnostics C) configuration D) diagnostics C) configuration D) diagnostics
P) performance/status B) circuit
P) performance/status B) circuit P) performance/status B) circuit P) performance/status B) circuit
X) system log off
X) system log off X) system log off X) system log off
[1,1] QUAD 2164 > [1,1] QUAD 2164 > [1,1] QUAD 2164 > [1,1] QUAD 2164 >