Westermo PMI-110-F2G User Manual

Page 83

Advertising
background image

Region Revision: 
Switch(config‐mst)# revision 
    <0‐65535>    the value of revision 
Switch(config‐mst)# revision 65535

Mapping Instance to 
VLAN (Ex: Mapping 
VLAN 2 to Instance 1) 

Switch(config‐mst)# instance 
    <1‐15>    target instance number 
Switch(config‐mst)# instance 1 vlan 
    VLANMAP    target vlan number(ex.10) or range(ex.1‐10) 

Switch(config‐mst)# instance 1 vlan 2

Display Current MST 
Configuraion 

Switch(config‐mst)# show current 
Current MST configuration 
Name            [Westermo] 
Revision    65535 
Instance    Vlans Mapped 
‐‐‐‐‐‐‐‐    ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 

  0                1,4‐4094 
  1                2 
  2                3 

‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 
Config HMAC‐MD5 Digest: 
0xB41829F9030A054FB74EF7A8587FF58D 
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐

Remove Region Name 

Switch(config‐mst)# no 

  name            name configure 
  revision    revision configure 
  instance    the mst instance 

Switch(config‐mst)# no name

Remove Instance 
example 

Switch(config‐mst)# no instance 

  <1‐15>    target instance number 

Switch(config‐mst)# no instance 2

Show Pending MST 
Configuration 
 

Switch(config‐mst)# show pending 
Pending MST configuration 
Name            []       

(‐>The name is removed by no name)

 

Revision    65535 
Instance    Vlans Mapped 
‐‐‐‐‐‐‐‐    ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 

  0                1,3‐4094 
  1                2       

  (‐>Instance 2 is removed by no instance 2)

 

‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 
Config HMAC‐MD5 Digest: 
0x3AB68794D602FDF43B21C0B37AC3BCA8 
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐

Apply the setting and 
go to the configuration 
mode 

Switch(config‐mst)# quit 
apply all mst configuration changes 
Switch(config)#

Apply the setting and 
go to the global mode 

Switch(config‐mst)# end 
apply all mst configuration changes 
Switch#

Abort the Setting and 
go to the configuration 
mode. 
 
Show Pending to see 
the new settings are 
not applied. 

Switch(config‐mst)# abort 
discard all mst configuration changes 
Switch(config)# spanning‐tree mst configuration 
Switch(config‐mst)# show pending 
Pending MST configuration 
Name            [Westermo] 

(‐>The nameis not applied after Abort settings.)

 

Revision    65535 
Instance    Vlans Mapped 
‐‐‐‐‐‐‐‐    ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐

79

Advertising