Panasonic TH-65SQ1WA 65" Class 4K HDR Commercial Monitor - Manual (Page 71)

71
English
■
[PC power management] (DPMS function)
When this function is set to [On], it operates under
the following conditions to turn the power on or off
automatically.
When no pictures (HD/VD sync signals) are
detected for 60 seconds or so at PC input:
Power is turned off (standby); the power indicator
lights up orange.
When pictures (HD/VD sync signals) are
subsequently detected at PC input:
Power is turned on; the power indicator lights up
green.
Note
● This function is effective when [Sync] in [Signal] is set
to [Auto] or [HV sync] and [Component/RGB-in select]
are set to [RGB]. (see page 60)
● This function may not operate depending on the video
output devices.
■
[Power save]
This function adjusts the brightness of the backlight to
reduce power consumption.
[Off]:
The power save function does not operate.
[On]:
Backlight brightness is reduced.
■
[Extended standby mode]
Sets the operation in standby mode by the “Power
management” function for the input terminal for which
the “Power management” function is set to [On].
[Off]:
If a video signal (synchronized signal) is detected
at the input terminal with which the standby mode
is entered, the power is turned “ON” with the input.
[On]:
If a video signal (synchronized signal) is detected
at any of the input terminals for which the “Power
management” function is set to [On], the power
is turned “ON”, and the input is switched to the
detected input.
Note
● When [Input search] is [All inputs] or [Custom], the
[Input search] function is prioritised. (The “Power
management” function does not operate for each
terminal.) (For details of [Input search] function, see
page 64.)
● When [Failover/Failback] - [Input change mode] is
set to items other than [Off], the [Failover/Failback]
function is prioritised. (The “Power management”
function does not operate for each terminal.) (For
details of [Failover/Failback] function, see page 65.)
■
[Changing delay]
Sets the delay time until the input is switched when
[Power management mode] is [Input detection].
[Off]:
Switches the input if a signal is interrupted even for
a very short period.
1 to 10:
Sets the delay time (sec.). Switches the input when
the set time has elapsed after detecting no signal
is present. However, if the detection period during
which no signal is present is shorter than the set
delay time, the input is not switched.
Note
● The operation when [Input detection] is selected is the
same as the operation when [Input search] is set to
[Input detection]. (see page 64)
Audio input select
[Audio input select] - submenu screen
HDMI1
HDMI2
DVI-D
PC
HDMI2
HDMI1
Audio input select
DisplayPort DisplayPort
DIGITAL LINK DIGITAL LINK
AUDIO IN1
AUIDIO IN2
SLOT SLOT
Screen Transfer Screen Transfer
Video input Audio input
HDMI1
HDMI1 / AUDIO IN1 / AUIDIO
IN2 / No audio
HDMI2
HDMI2 / AUDIO IN1 / AUIDIO
IN2 / No audio
DisplayPort
DisplayPort / AUDIO IN1 /
AUIDIO IN2 / No audio
DIGITAL LINK
DIGITAL LINK / AUDIO IN1 /
AUIDIO IN2 / No audio
DVI-D / PC AUDIO IN1 / AUIDIO IN2 / No
audio
SLOT
SLOT / AUDIO IN1 / AUIDIO
IN2 / No audio
Screen Transfer
Screen Transfer / AUDIO IN1 /
AUIDIO IN2 / No audio
● No audio: No audio input (Mute)
When the setting for the audio input has been
changed from the factory settings, the audio input is
displayed as below.
HDMI1
Full
AUDIO IN1