Roland RD-700 User Manual
Page 101
101
Troubleshooting
Appendices
Effects Not Ap-
plied/Effects
Sound Wrong
In some cases where the delay timing
selected in the DELAY settings in
MFX/Reverb/Chorus is set to a note
value, the delay sound may not be
heard. Either adjust the tempo or
change the numerical value of the de-
lay timing (p. 79).
Check the MFX Source and MFX Dest
settings for multi-effect that is not
sounding in the Lower Part to which
it is applied (p. 77).
• With certain settings, the Lower
Part’s MFX settings are disregard-
ed.
No Pitch Bend
When Pitch
Bend Lever is
Moved
Is the Tone Wheel screen appearing
in the display?
• The pitch bend effect cannot be ap-
plied with the pitch bend lever
while the Tone Wheel screen is in
the display. In this case, the pitch
bend lever functions as a slow/fast
switch for the Rotary effect (p. 75).
Sounds Come
From Left or
Right Each Time
Key is Pressed
(Panned)
In some Tones, the settings are such
that sounds randomly play from the
left or right side (are panned) each
time the keys are pressed. These set-
tings cannot be changed.
Sound is Distort-
ed
Sounds can be distorted due to
equalizer, multi-effect, and Part vol-
ume settings. Adjust the following
settings.
• PART LEVEL sliders (p. 45).
• Edit mode MFX/Reverb/Chorus
MFX <Other Prm> effect levels (p.
77).
• System Master Volume settings (p.
Is a distortion-type effect being ap-
plied to the sound (p. 77, p. 80)?
Cannot Select
the Draw Bar
Screen (Tone
Wheel Screen)
The screen is displayed by selecting a
Organ Tone (Tone Wheel 1~10) for
any of the UPPER1, UPPER2, or
LOWER Parts in the Tone screen, and
then pressing CURSOR [ ] (p. 75).
Key Range Set-
tings Not Effec-
tive
Is [SPLIT] set to OFF?
• Key Range goes into effect when
[SPLIT] set to ON (p. 63, p. 88).
Problem
Check/Solution
Tempo Doesn’t
Change
Is the System Clock Source setting in
Edit mode set to MIDI?
• When you want to perform using
the RD-700’s tempo, set this to
“INT” (p. 70).
Pitch is Odd
Depending on the Tone selected,
pitches played in certain registers
will be changed and played at other
pitches.
Is Coarse Tune, Fine Tune, or Stretch
Tune set for any specific Part?
• Check the Tone Edit Course Tune,
Fine Tune and Stretch Tune set-
tings in Edit mode (p. 80, p. 81), or
C.T and F.T setting in MIDI TX
screen.(p. 65).
Has the RD-700 gone out of tune?
Check the System Master Tune set-
tings in Edit mode (p. 29).
Has the pitch been changed by pedal
operations or by Pitch Bend messag-
es received from an external MIDI
device?
Sound is Cut Off
When you try playing more than the
maximum 128 voices simultaneous-
ly, sounds currently being played
may be cut out.
• Increase the Voice Reserve settings
for the Parts you do not want to
have cut off (p. 90).
Sound Keeps
Playing When
Key is Pressed
Is the hold pedal polarity reversed?
• Check the System Pedal Polarity
settings in Edit mode (p. 71).
Exclusive Mes-
sages Cannot
Be Received
Is the Device ID number of the trans-
mitting device matched to the RD-
700’s Device ID number?
• Check the System Device ID set-
Is the RD-700 set to GM mode?
• Press ONE TOUCH [PIANO] or
[SETUP] to exit GM mode (p. 98).
Setup Name Not
Correctly Indi-
cated
When a Setup name is registered (p.
56), names with eight or more of the
letters M, N, or W are not displayed
correctly. Try reducing the number
of these letters.
Problem
Check/Solution
RD-700_e.book 101 ページ ２００３年１０月２３日 木曜日 午後４時５９分