Roland RD-700 - Manual (Page 124)

124
Effect/Parameter List
Appendices
Cutoff (Cutoff Frequency)
Sets the cutoff frequency when a specific frequency band is cut
off by a filter.
StpRateSw (Step Rate Switch)
Determines whether the pitch is changed in a stepped fashion
(ON) or not (OFF).
Step Rate #
Adjust the rate at which the pitch will change.
➔
Step Rate parameter can be set as a note-value of a tempo. In
this case, specify the value of the desired note.
Out (Output Mode)
Adjust the method that will be used to hear the output sound.
The optimal 3D effect will be achieved if you select SPEAKER
when using speakers, or PHONES when using headphones.
Low Gain
Adjust the low frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the high frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance #
Adjust the volume balance between the direct sound and the
flanger sound.
With a setting of D100:0W only the direct sound will be output,
and with a setting of D0:100W only the flanger sound will be
output.
Level (Output Level)
Adjust the output level.
62: TREMOLO
Tremolo cyclically modulates the volume to add tremolo effect
to the sound.
Mod Wave (Modulation Wave)
TRI : The sound will be modulated like a triangle wave.
SQR : The sound will be modulated like a square wave.
SIN : The sound will be modulated like a sine wave.
SAW1/2 : The sound will be modulated like a sawtooth wave.
The teeth in SAW1 and SAW2 point at opposite directions.
Rate #
Adjust the frequency (speed) of the change.
➔
Rate parameter can be set as a note-value of a tempo. In this
case, specify the value of the desired note.
Depth #
Sets the depth to which the effect is applied.
Low Gain
Adjust the low frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the high frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the high frequency
range.
Level (Output Level)
Adjust the output level.
63: AUTO PAN
The Auto Pan effect cyclically modulates the stereo location of
the sound.
Mod Wave (Modulation Wave)
TRI : The sound will be modulated like a triangle wave.
SQR : The sound will be modulated like a square wave.
SIN : The sound will be modulated like a sine wave.
SAW1/2 : The sound will be modulated like a sawtooth wave.
The teeth in SAW1 and SAW2 point at opposite directions.
Rate #
Adjust the frequency (speed) of the change.
➔
Rate parameter can be set as a note-value of a tempo. In this
case, specify the value of the desired note.
Depth #
Sets the depth to which the effect is applied.
Low Gain
Adjust the low frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the high frequency gain (amount of boost or cut).
Positive (+) settings will emphasize (boost) the high frequency
range.
Level (Output Level)
Adjust the output level.
64: SYM.RESONANCE
(Sympathetic Resonance)
When you depress the damper pedal on an acoustic piano, the
sound from the strings that were struck resonates with other
strings, adding rich reverberations and broadness to the sound.
This effect simulates the resonance, called “Sympathetic
Resonance.”
Depth
Adjust the depth of Sympathetic Resonance.
Damper
This is controlled by a normal damper pedal, with the
resonance setting corresponding to the amount the pedal is
pressed.
Pre LPF
This sets the reference frequency for the low-end input cutoff
filter.
Pre HPF
This sets the reference frequency for the high-end input cutoff
filter. When not cutting bass frequencies, set this to BYPASS.
RD-700_e.book 124 ページ ２００３年１０月２３日 木曜日 午後４時５９分