Roland RD-700 - Manual (Page 109)

109
Effect/Parameter List
Appendices
Mode (Feedback Mode)
Select the way in which delay sound is fed back into the effect.
NORMAL : The left delay sound will be fed back into the left
delay, and the right delay sound into the right delay.
CROSS : The left delay sound will be fed back into the right
delay, and the right delay sound into the left delay.
Phase L (Feedback Phase Left)
Select the phase of the left delay sound.
NORMAL : Phase is not changed.
INVERT : Phase is inverted.
Phase R (Feedback Phase Right)
Select the phase of the right delay sound.
NORMAL : Phase is not changed.
INVERT : Phase is inverted.
HF Damp
Adjust the frequency above which sound fed back to the effect
will be cut. If you do not want to cut the high frequencies of the
feedback, set this parameter to BYPASS.
Low Gain
Adjust the gain of the low frequency range.
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the gain of the high frequency range.
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance) #
Adjust the volume balance between the direct sound and the
delay sound. With a setting of D100:0W only the direct sound
will be output, and with a setting of D0:100W only the delay
sound will be output.
Level (Output Level)
Adjust the output level.
18: MOD DELAY (Modulation Delay)
This effect adds modulation to the delayed sound, producing an
effect similar to a flanger.
Delay L (Delay Time Left)
Adjust the time from the direct sound until when the left delay
sound is heard.
Delay R (Delay Time Right)
Adjust the time from the direct sound until when the right
delay sound is heard.
Feedback (Feedback Level)
Adjust the proportion (%) of the delay sound that is fed back
into the effect. Negative (-) settings will invert the phase.
Mode (Feedback Mode)
Select the way in which delay sound is fed back into the effect.
NORMAL : The left delay sound will be fed back into the left
delay, and the right delay sound into the right delay.
CROSS : The left delay sound will be fed back into the right
delay, and the right delay sound into the left delay.
Rate #
Adjust the speed of the modulation.
Depth
Adjust the depth of the modulation.
Phase
Adjust the spatial spread of the sound.
HF Damp
Adjust the frequency above which sound fed back to the effect
will be cut. If you do not want to cut the high frequencies of the
feedback, set this parameter to BYPASS.
Low Gain
Adjust the gain of the low frequency range.
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the gain of the high frequency range.
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance) #
Adjust the volume balance between the direct sound and the
modulation delay sound. With a setting of D100:0W only the
direct sound will be output, and with a setting of D0:100W only
the modulation delay sound will be output.
Level (Output Level)
Adjust the output level.
19: TRI TAP DLY (Triple Tap Delay)
The Triple Tap Delay produces three delay sounds; center, left
and right.
Delay C (Delay Time Center)
Adjust the time delay from the direct sound until when the
center delay sound is heard.
Delay L (Delay Time Left)
Adjust the time delay from the direct sound until when the left
delay sound is heard.
Delay R (Delay Time Right)
Adjust the time delay from the direct sound until when the
right delay sound is heard.
➔
Delay C, Delay L and Delay R parameters can be set as a note-
value of a tempo. In this case, specify the value of the desired
note.
Feedback (Feedback Level) #
Adjust the proportion (%) of the delay sound that is fed back
into the effect. Negative (-) settings will invert the phase.
Level C (Center Level)
Adjust the volume of the center delay sound.
Level L (Left Level)
Adjust the volume of the left delay sound.
Level R (Right Level)
Adjust the volume of the right delay sound.
RD-700_e.book 109 ページ ２００３年１０月２３日 木曜日 午後４時５９分