Roland RD-700 - Manual (Page 110)

110
Effect/Parameter List
Appendices
HF Damp
Adjust the frequency above which sound fed back to the effect
will be cut. If you do not want to cut the high frequencies of the
feedback, set this parameter to BYPASS.
Low Gain
Adjust the gain of the low frequency range.
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the gain of the high frequency range.
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance) #
Adjust the volume balance between the direct sound and the
delay sound. With a setting of D100:0W only the direct sound
will be output, and with a setting of D0:100W only the delay
sound will be output.
Level (Output Level)
Adjust the output level.
20: QUAD TAP DLY (Quadruple Tap Delay)
The Quadruple Tap Delay has four delays.
The stereo location of each delay sound is as follows.
fig.MFX-20b
Delay 1 (Delay Time 1)
Adjust the time delay from the direct sound until when delay 1
sound is heard.
Delay 2 (Delay Time 2)
Adjust the time delay from the direct sound until when delay 2
sound is heard.
Delay 3 (Delay Time 3)
Adjust the time delay from the direct sound until when delay 3
sound is heard.
Delay 4 (Delay Time 4)
Adjust the time delay from the direct sound until when delay 4
sound is heard.
➔
Delay 1–4 parameters can be set as a note-value of a tempo. In
this case, specify the value of the desired note.
Level 1
Adjust the volume of delay 1 sound.
Level 2
Adjust the volume of delay 2 sound.
Level 3
Adjust the volume of delay 3 sound.
Level 4
Adjust the volume of delay 4 sound.
Feedback (Feedback Level) #
Adjust the proportion (%) of the delay sound that is fed back
into the effect. Negative (-) settings will invert the phase.
HF Damp
Adjust the frequency above which sound fed back to the effect
will be cut. If you do not want to cut the high frequencies of the
feedback, set this parameter to BYPASS.
Balance (Effect Balance) #
Adjust the volume balance between the direct sound and the
delay sound. With a setting of D100:0W only the direct sound
will be output, and with a setting of D0:100W only the delay
sound will be output.
Level (Output Level)
Adjust the output level.
21: TIME CTRL DLY (Time Control Delay)
You can use MIDI messages assigned to the Control knob to
make changes in the delay time and pitch in real time.
Lengthening the delay will lower the pitch, and shortening it
will raise the pitch.
Delay (Delay time) #
Adjust the time delay from the direct sound until when each
delay sound is heard.
Accel (Acceleration)
This parameter adjusts the time over which the Delay Time will
change from the current setting to a newly specified setting. The
rate of change for the Delay Time directly affects the rate of
pitch change.
Feedback (Feedback Level) #
Adjust the proportion (%) of the delay sound that is fed back
into the effect. Negative (-) settings will invert the phase.
HF Damp
Adjust the frequency above which sound fed back to the effect
will be cut. If you do not want to cut the high frequencies of the
feedback, set this parameter to BYPASS.
Pan (Output Pan)
Adjust the stereo location of the delay sound. L64 is far left, 0 is
center, and 63R is far right.
Low Gain
Adjust the gain of the low frequency range.
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the gain of the high frequency range.
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance)
Adjust the volume balance between the direct sound and the
delay sound. With a setting of D100:0W only the direct sound
will be output, and with a setting of D0:100W only the delay
sound will be output.
1
2 3
4
L R
RD-700_e.book 110 ページ ２００３年１０月２３日 木曜日 午後４時５９分