BINDER VD 23 User Manual

Operating manual, Apt.line™ vdl (e2.1), Vacuum drying ovens for flammable solvents

Advertising

This manual is related to the following products:

VD 53, VD 115, VDL 23, VDL 53, VDL 115

Table of contents

Document Outline

EC – Declaration of Conformity
TÜV Certificate
Product registration
1. Safety
- 1.1 Legal considerations
- 1.2 Structure of the safety instructions
- 1.3 Localization / position of safety labels on the unit
- 1.4 Type plate
- 1.5 General safety instructions on installing and operating the vacuum drying oven
- 1.6 Intended use
  - 1.6.1 Operation log
2. Description of the equipment
- 2.1 Safety equipment
- 2.2 Overview of the oven
- 2.3 VDL control panel
- 2.4 Connections at the rear of the unit
- 2.5 “Temperature setting” information panel (ignition temperature vs. drying temperature)
- 2.6 Overview of the zone classification of the ovens
3. Completeness of delivery, transportation, storage, and installation
- 3.1 Unpacking, and checking equipment and completeness of delivery
- 3.2 Guidelines for safe lifting and transportation
- 3.3 Storage
- 3.4 Location of installation and ambient conditions
4. Installation and connections
- 4.1 Vacuum expansion racks
- 4.2 Vacuum connection
  - 4.2.1 Notes regarding use of vacuum pumps of other manufacturers
- 4.3 Inert gas connection
- 4.4 Compressed air / inert gas connection for sweeping the area for electrical equipment
- 4.5 Electrical connection
5. Start up
- 5.1 Settings at the RD3 program controller
- 5.2 General indications
6. Fixed value entry mode
7. Week program editor
- 7.1 Program table template for the Week Program Editor
- 7.2 Programming example of the Week program editor
8. Program editor
- 8.1 Selecting between set-point ramp and set-point step
- 8.2 Set-point entry for program operation
- 8.3 Program table template
- 8.4 Deleting a program section
9. Program start level
10. User level
11. Performance in case of failures
- 11.1 Performance after power failures
- 11.2 Alarm messages
12. Safety device class 2 (DIN 12880)
13. Reference measurements. Checking the temperature in the inner chamber
14. Commissioning the vacuum
- 14.1 Evacuation
- 14.2 Breaking the vacuum (flooding with ambient air)
- 14.3 Operation with inert gas
15. Options
- 15.1 ATEX connection kits for vacuum pumps VP4 or VP5 (option)
- 15.2 Vacuum module empty (without pump) (option)
- 15.3 Vacuum module with chemical membrane pump VP4 or VP5 (option)
- 15.4 Additional measuring channel for digital object temperature display with flexible Pt 100 temperature sensor (option)
- 15.5 Measuring access port vacuum 9 poles (option)
- 15.6 Communication software APT-COM™ 3 DataControlSystem (option)
16. Maintenance, cleaning, and service
- 16.1 Maintenance intervals, service
- 16.2 Cleaning and decontamination
  - 16.2.1 Cleaning
  - 16.2.2 Decontamination
- 16.3 Sending the unit back to BINDER GmbH
17. Disposal
- 17.1 Disposal of the transport packing
- 17.2 Decommissioning
- 17.3 Disposal of the unit in the Federal Republic of Germany
- 17.4 Disposal of the unit in the member states of the EC except for the Federal Republic of Germany
- 17.5 Disposal of the unit in non-member states of the EC
18. Troubleshooting
19. Technical description
- 19.1 Factory calibration and adjustment
- 19.2 VDL technical data
- 19.3 Equipment and Options
- 19.4 Spare parts
- 19.5 Dimensions VDL 23
- 19.6 Dimensions VDL 53
- 19.7 Dimensions VDL 115
20. Contamination clearance certificate
- 20.1 For units located outside North America and Central America
- 20.2 For units in North America and Central America
Word-Lesezeichen
- OLE_LINK18
- OLE_LINK19
- OLE_LINK10
- OLE_LINK1
- OLE_LINK4
- OLE_LINK7
- OLE_LINK8

Popular Brands

Popular manuals