Super Systems 3L Series - Manual (Page 45)

Series 3L Indicators
45
46 – Timer Run/Reset
47 – Timer Hold
48 – Auto/Manual Select
49 – Standby Select
L.SENS Configures the polarity of the logic
input channel A (0 = Normal, 1 =
Inverted) 12361
L.TYPE
(LB)
Logic Input B channel hardware
type
0 – None
1 – Logic Inputs 12362
L.D.IN
(LB)
Logic input B function)
40 – None
41 – Acknowledge all alarms
42 – Select SP1/2
43 – Lock All Keys
44 – Timer Reset
45 – Timer Run
46 – Timer Run/Reset
47 – Timer Hold
48 – Auto/Manual Select
49 – Standby Select 12363
L.SENS
(LB) Configures the polarity of the logic
input channel B (0 = Normal, 1 =
Inverted) 12377
ID
Comms Module Type
0 – None
1 – RS485
2 – RS232 12544
BAUD
Baud Rate
0 – 9600
1 – 19200
2 – 4800
3 – 2400
4 – 1200 12548
PRTY
Parity setting
0 – None
1 – Even
2 – Odd 12549
DELAY RX/TX Delay – (0 = no delay, 1 =
delay) Select if a delay is required
between received and transmitted
comms messages. Sometimes
required when intelligent RS485
adaptors are used. 12550
RETRN Comms Retransmission Variable
selection:
0 – Off
1 – Working Setpoint
2 – PV
3 – Output Power
4 – Error 12551
REG.AD Modbus register address to
broadcast retransmission to. For
example if you wish to retransmit
the working setpoint from one
Series 3L to a group of slaves, and
receive the master working setpoint
into the slaves’ remote setpoint, set
this variable to 26 (the address of
the remote setpoint in the slave
units). 12552
Cal 3 offset 12558
Cal 4 offset 12559
1.ID
IO channel 1 hardware type
0 – None
1 – Relay 12672
1.FUNC
I/O Channel Function
0 – None (or Telemetry Output) 12674
1 – Digital Output
1.SRC.A IO Channel 1 Source A
0 – None
1 – Alarm 1
2 – Alarm 2
3 – Alarm 3
4 – Alarm 4
5 – All Alarms (1-4)
6 – New Alarm
9 – Sensor Break Alarm 12677
1.SRC.B
IO Channel 1 Source B
As IO Channel 1 Source A (Modbus
address 12678) 12678
1.SRC.C
IO Channel 1 Source C
As IO Channel 1 Source A (Modbus
address 12678) 12679
1.SRC.D
IO Channel 1 Source D
As IO Channel 1 Source A (Modbus
address 12678) 12680
1.SENS Configures the polarity of the input
or output channel (0 = Normal, 1 =
Inverted) 12681
IO1 high 12682
IO1 telemetry 12683
3.ID
Output 3 Type
0 – None
1 – Relay 12800
3.FUNC
Output 3 Channel function
0 – None (or Telemetry Output)
1 – Digital Output
12803
3.SRC.A
Output 3 source A
As IO Channel 1 Source A (Modbus
address 12678) 12806
3.SRC.B
Output 3 source B
As IO Channel 1 Source A (Modbus
address 12678) 12807
3.SRC.C Output 3 source C
As IO Channel 1 Source A (Modbus
address 12678) 12808
3.SRC.D
Output 3 source D
As IO Channel 1 Source A (Modbus
address 12678) 12809
3.SENS Output 3 Polarity (0 = Normal, 1 =
Inverted) 12810
Output 3 telemetry 12812
4.TYPE
Output AA Type
0 – None
1 – Relay 13056
4.FUNC Output 4 Channel function
0 – None (or Telemetry Output)
1 – Digital Output 13059
4.SRC.A
Output AA source A
As IO Channel 1 Source A (Modbus
address 12678) 13062
4.SRC.B
Output AA source B
As IO Channel 1 Source A (Modbus
address 12678) 13063
4.SRC.C
Output AA source C
As IO Channel 1 Source A (Modbus
address 12678) 13064
4.SRC.D
Output AA source D
As IO Channel 1 Source A (Modbus
address 12678) 13065
4.SENS Output AA sense (0 = Normal, 1 =
Inverted) 13066