Roland VR-6HD Direct Streaming AV Mixer - Manual (Page 101)

101
Menu List
Menu item Value (bold text: default value) Explanation
DELAY
0 .0 –500msec
(0 –25.0/29.9/30.0frame)
Adjusts the delay time of the audio.
Effect Outputs audio with a delay.
REVERB SEND 0 –127 Adjusts the amount of audio sent to reverb.
MAIN BUS This configures the MAIN bus.
SEND OFF, ON When this is “ON”, audio is sent to the MAIN bus.
AUX 1 BUS This configures the AUX 1 bus.
SEND LEVEL -INF –10.0dB These parameters adjust the amount of audio sent to the AUX 1 bus.
SEND POINT
DRY Sends the source audio with no effects applied.
PRE FADER
Sends the effect-applied audio.
The send volume is constant, regardless of the volume (INPUT LEVEL).
POST FADER
Sends the effect-applied audio.
The send volume can be changed by adjusting the volume (INPUT LEVEL).
AUX 2 BUS This configures the AUX 2 bus.
SEND LEVEL -INF –10.0dB These parameters adjust the amount of audio sent to the AUX 2 bus.
SEND POINT
DRY Sends the source audio with no effects applied.
PRE FADER
Sends the effect-applied audio.
The send volume is constant, regardless of the volume (INPUT LEVEL).
POST FADER
Sends the effect-applied audio.
The send volume can be changed by adjusting the volume (INPUT LEVEL).
HIGH PASS FILTER 80Hz OFF , ON
Turns the high-pass filter on/off.
Effect Cuts off unneeded low-band audio. The cutoff frequency is 80 Hz.
NOISE GATE OFF , ON
Turns the noise gate on/off.
Effect
Eliminates audio that is lower than the specified threshold level. This is effective when the
noise that you want to remove is separate from the audio that you want to keep, and can be
used to remove hiss or other noise that is heard during periods of silence.
THRESHOLD -80– -48 –0dB
Specifies the level used as the threshold for removing audio. Audio below the level set
here is removed.
RELEASE 30– 500 –5000msec
Adjusts the length of time until the audio is fully attenuated after audio falls below the
threshold.
DE-ESSER OFF , ON
Turns the de-esser on/off.
Effect Reduces sibilant noise (the sounds you hear when pronouncing “s” words and other hissing
sounds).
SENS 0– 80 –100 Adjusts the sensitivity with which sibilants are detected.
DEPTH 0– 64 –100 Adjusts the intensity of the effect.
COMPRESSOR OFF , ON
Turns the compressor on/off.
Effect
Audio that exceeds the specified threshold level is compressed. This reduces the difference
between the maximum volume and minimum volume, making the audio more comfortable
for listening
THRESHOLD -50– -8 –0dB
Specifies the level used as the threshold at which the compressor is applied.
Compression is applied to audio that exceeds the threshold.
RATIO
1.00:1, 1.12:1, 1.25:1, 1.40:1,
1.60:1, 1.80:1, 2.00:1,
2 .50:1 ,
3.20:1, 4.00:1, 5.60:1, 8.00:1,
16.0:1, INF:1
Specifies the degree of compression applied to the audio. The state in which no
compression is applied is defined as “1”.
ATTACK 0– 30 –100msec Specifies the time until compression starts when audio exceeding the threshold is input.
RELEASE 30– 250 –5000msec Adjusts the length of time until compression ends after audio falls below the threshold.
MAKEUP GAIN -40– 0 –40dB Adjusts the final output volume level after applying the compressor.
EQUALIZER OFF , ON
Turns the equalizer on/off.
Effect This is a 4-band parametric equalizer. It lets you shape the character of the sound by
boosting or cutting four frequency regions.
Hi GAIN -12.0– 0 .0 –12.0dB Boosts or attenuates the high band.
Hi FREQUENCY 1.00– 10 .0 –20.0kHz Adjusts the center frequency when changing the tone quality in the high band.
Hi-Mid GAIN -12.0– 0 .0 –12.0dB Boosts or attenuates the high-midrange band.
Hi-Mid FREQUENCY 20Hz– 2 .00kHz –20.0kHz Adjusts the center frequency when changing the tone quality in the high-midrange band.
Hi-Mid Q 0.5– 1 .0 –16.0 Adjusts the width of the frequency band when boosting or attenuating high-midrange band.
Lo-Mid GAIN -12.0– 0 .0 –12.0dB Boosts or attenuates the low-midrange band.
Lo-Mid FREQUENCY 20Hz– 500Hz –20.0kHz Adjusts the center frequency when changing the tone quality in the low-midrange band.
Lo-Mid Q 0.5– 1 .0 –16.0
Adjusts the width of the frequency band when boosting or attenuating low-midrange
band.
Lo GAIN -12.0– 0 .0 –12.0dB Boosts or attenuates the low band.
Lo FREQUENCY 20Hz– 100Hz –2.00kHz Adjusts the center frequency when changing the tone quality in the low band.
(*3) When “STEREO LINK” is “ON”, the [4]–[6] fader operations are disabled.
(*4) This can be set if “STEREO LINK” is “OFF”.