Document Outline

• Cover
• Copyright
• Table of Contents
• Warnings
• Specifications and Operating Requirements
  • Introduction
    • Conventions Used In This Manual
    • Technical Support
    • Your Dyno Room
  • Dynamometer Specifications and Requirements
    • Battery Requirements
    • Chassis Specifications
    • Compressed Air Requirements
    • Computer Specifications
    • Electrical Requirements
    • Environmental Requirements
    • Forklift Requirements
    • Ground Hook Requirements
    • Phone and Internet Access
    • Tie-Down Straps
  • Model 200iP/250iP Motorcycle Pit Dynamometer
  • Dyno Electronics
• Installation
  • Unpacking and Installing the Dyno
    • Uncrate the Dyno
    • Verifying the Pit Dimensions
    • Removing the Dyno from the Crate
  • Eddy Current Brake
    • Parts List
    • Unpacking the Eddy Current Brake
    • Installing the Eddy Current Brake
    • Securing the Drum and Brake Module to the Pit Floor
  • Pickup Card
  • Carriage Plate and Tire Carriage
    • Installing the Carriage Plate
    • Installing the Tire Carriage
  • Blower Mounts, Support Arm and Junction Box
    • Mark and Drill Blower Mounts and Support Arm Mounting Holes
    • Installing the Blower Mounting Plate, Support Arm, and Junction Box
    • Installing the Arms and Monitor Tray
  • Routing Cables
    • Battery Requirements
    • Installing the Battery
    • Accessing the CPI
    • Routing the Control Panel, Pendant Cables, and RPM Cable
    • Routing the High Pressure Blower Cables
    • Routing the Power Carriage and Wheel Clamp Cables
    • Routing the Eddy Current Brake, Battery, and Dyno Power Cables
    • Routing the Pickup Card and Dyno Electronics Cables
    • Routing the Air Pump Power, Air Fuel Sensor, and Dyno Electronics Power Cables
    • Wiring the Breakout Board
  • Final Adjustments and Tests
    • Turning On the Dyno Power
    • Power Carriage Final Adjustments and Tests
    • Wheel Clamp Final Adjustments and Tests
  • Pit Covers
    • Changing the Retarder Cover for Right Side Installations
    • Installing the Pit Covers
  • Junction Box Cover, Cable Cover, and End Cap
  • Zip Tube
• Accessories
  • Main Dyno Power
  • Air Brake
    • Parts List
    • Routing the Air Brake Cable and Air Hose
    • Installing the Emergency Stop Sticker
    • Air Brake Final Adjustments and Tests
    • Changing the Brake Pads
    • Adjusting the Brake Pad Clearance
  • Air Pump and Filter Assembly
  • Extended Carriage
    • Parts List
    • Installing the Extended Carriage Plate
    • Installing the Extended Tire Carriage
  • High Pressure Blower
    • Parts List
    • Installing the High Pressure Blowers
    • Attaching the Blower Cables
  • Wheel Clamp
    • Installing the Wheel Clamp
    • Wheel Clamp Final Adjustments and Tests
• Control Panel Interface Operation
  • Basic CPI Operation
    • Using the Air Fuel Ratio Air Pump
    • Using the Emergency Stop/Dyno Shutdown
    • Using the High Pressure Blowers
    • Understanding Interlocks
    • Using the Power Carriage
    • Using the Starter
    • Using the Status Indicator
    • Using the Wheel Clamp
  • Power Distribution Assembly
    • Main Circuit Breaker
    • High Pressure Blower Circuit Breakers
  • Maintenance and Troubleshooting
    • Maintaining and Troubleshooting the Wheel Clamp
    • Replacing the Theta Controller Fuses
    • Troubleshooting CPI Fuses
• Basic Dyno Operation
  • Loading the Bike
  • Connecting the RPM Pickup
    • RPM Pickup Descriptions
    • Connecting the Primary Inductive Pickup
    • Connecting the Secondary Inductive Pickup
  • Pre-run Inspection
    • Before Starting the Engine
    • Engine Warm Up
    • After Engine Warm Up
  • Making a Test Run
  • Preventative Maintenance
• Red Head Anchor Installation
  • Warnings
  • Contact Information for ITW Ramset/Red Head
  • Installation
• Power Requirements
  • Locations using 60Hz Power (North America & Japan)
    • Installing the Wall Receptacle
    • Testing for Correct Voltages
    • Replacing the Power Plug
    • Hard Wiring to the Building
    • Connecting the Dyno
  • Locations Using 50 Hz Power (Locations Other than North America and Japan)
    • Installing the Wall Receptacle
    • Testing for Correct Voltages
    • Replacing the Power Plug
    • Hard Wiring to the Building
    • Connecting the Dyno
• EEC Finger Guard and Door Safety Switch Installation
  • EEC Finger Guards
    • Installing the EEC Finger Guards
    • Adjusting the EEC Finger Guards
  • Door Safety Switch
    • Installing the Door Safety Switch
• Theta Controller
  • Power Adjustment
    • Accessing the Dip Switches
• Index