Yaskawa E7 Drive User Manual - Manual (Page 233)

Index - 1
A
A. TUNE menu........................................................3-7, 3-14
AC Reactor .......................................................................E-4
Accel/Decel
Parameters ................................................................ A-7
Time......................................................................... 5-25
Acceleration
Stall Prevention Level during.............. 5-40, 6-17, A-20
Time.................................................................5-25, A-7
Troubleshooting....................................................... 6-17
Access Level.............................................................5-2, A-2
ADV menu...............................................................3-7, 3-13
Alarm Displays & Processing........................................... 6-9
ALARM Indicator ............................................................ 3-5
Altitude ............................................................................ C-4
Ambient Temperature ............................................. 1-13, C-4
Analog Inputs
Bias...................................................... 5-33, 5-38, A-16
Connection Diagram................................................ 2-18
Control Circuit Terminals........................................ 2-14
Gain ..................................................... 5-33, 5-38, A-16
Parameters ..............................................A-4, A-9, A-16
Troubleshooting....................................................... 6-15
Analog Outputs
Bias...............................................................A-17, A-18
Connection Diagram................................................ 2-18
Control Circuit Terminals........................................ 2-14
Gain ........................................................................ A-17
Parameters ....................................................A-17, A-18
Annunciation Contacts .................................................. A-15
APOGEE FLN.................................................. iv, A-18, D-1
ASIC Faults ...................................................................... 6-3
Auto
AUTO Key ................................................................ 3-3
Mode.......................................................................... 3-5
REF Indicator .....................................................3-2, 3-6
SEQ Indicator ....................................................3-2, 3-5
Auto Restart..........................................................5-44, A-21
Count Reset ............................................................. 5-44
Faults Covered......................................................... 5-45
Max. Restart Time After Fault ................................ 5-44
Number of Attempts................................................ 5-44
Auto-Tuning
Fault Displays and Processing................................. 6-13
How to ..................................................................... 5-59
Menu.................................................................3-7, 3-14
Motor Rated Current .............................................. A-25
Motor Rated Power ................................................ A-25
B
BAS Communication ....................................... iii, A-18, D-1
Base Block
After Fault..................................................... 5-44, A-19
Circuit Fault ...............................................................6-2
Minimum Time ....................................... 5-7, A-19, B-4
Basic Programming.............................................. 5-1 to 5-60
Baud Rate .............................................. 6-9, A-18, D-2, D-4
Bias Adjustments ..............................5-33, 5-38, A-16, A-17
Braking
DC Injection...................................................... 5-9, A-4
High-Slip.................................................................A-23
Branch Short Circuit Protection............................... E-2, E-3
Broken Belt (Undertorque detection)..............................5-46
C
Cable Length......................................................... 2-11, 6-18
Capacitors .........................................................................7-2
Capacity, Rated Output ........................................... C-2, C-3
Capacity Related Parameters .......................................... B-1
Carrier Frequency
Error .........................................................................6-12
Lower Limit ..............................................................A-8
Parameters.................................................................A-8
Proportional Gain......................................................A-8
Selection ...................................................................A-8
Upper limit........................................................A-8, B-3
Vs. Cable Length ........................................... 2-11, 6-18
Characteristic Frequency ................................................6-19
Charge Indicator (LED) ............................. 1-6, 2-2, 4-5, C-4
Circuit Breakers ................................................ 2-9, E-2, E-3
Clearances .......................................................................1-14
Coast to Stop ..........................................................................
....................... 5-6, 5-32, 5-48, A-4, A-11, A-18, A-19, A-22
Com OPT Setup Parameters..................................5-32, A-11
Communications Modbus/Serial....................... D-1 to D-14
Errors (CPF).............................................6-2 to 6-4, 6-9
Parameters...............................................................A-18
Components ................................................1-5, 1-6, 3-2, 7-2
Configuration
Electrical ................................................... 1-5, 1-6, 2-18
Physical......................................................... 1-7 to 1-10
Connections.................................................... 2-2, 2-14, 2-18
Preventive Maintenance.............................................7-3
Connectors
Inspection...................................................................7-2
Sizing .............................................................. 2-3 to 2-7
Contactors
Magnetic ................................................................... E-4
Soft Charge ............................................. 6-8, 6-11, 6-22
TM_E7_01_07182008.book Page 1 Wednesday, July 23, 2008 2:35 PM