Yaskawa E7 Drive User Manual - Manual (Page 239)

Index - 7
Function ........................................................... 5-21
Level ........................................................ 5-21, A-6
Square Root Gain ............................................ 5-23, A-6
PI Mode .................................................................. 5-15, A-5
PI Monitors
Feedback (U1-24).......................................... 5-20, A-27
Output (U1-37).............................................. 5-19, A-27
Setpoint (U1-38)............................................ 5-20, A-27
PLC (Programmable Logic Controller)
Serial Com. Using Modbus Protocol ....................... D-2
Plenum Rated ................................................................. 1-13
Potentiometer (Connection) ..................................2-12, 2-18
Power
Energy Saving ................................................. 5-24, A-7
Output, +15Vdc..............................................2-14, 2-18
Loss Ride-thru ...................................... 5-39, A-19, C-4
PCB
Inspecting........................................................... 7-2
Supply Specifications........................................C-2, C-3
Power Factor Correction Capacitors ................................ 6-6
Pre-Operation Considerations ................ i to iv; 1-1, 2-1, 4-1
Preset Speeds................................................................... A-8
Preventive Maintenance ................................................... 7-1
Programming
Basic..............................................................5-1 to 5-60
Error (OPE) ............................................................. 6-12
Menu .............................................................3-7 to 3-16
Protective
Functions ...................................................................C-4
Enclosure...................................................................C-4
Parameters .............................................................. A-22
PWM Frequency - See Carrier Frequency ...................... A-8
Q
Quick Setting Menu ................................................3-7, 3-12
R
Ramp to Stop ............................................................ 5-6, A-4
Rated Current, Motor ........ 4-6, 5-31, 6-13, A-11, A-25, B-4
Rdy (Ready) ..................................................................... 3-2
Reactors, Preventive Maintenance ................................... 7-3
READ ................................................................... 5-56, A-25
Ready Display .................................................................. 3-2
Receiving.......................................................................... 1-3
REF Indicator .....................................................3-2, 3-5, 3-6
Reference Limits (see Frequency).................5-26, 6-19, A-9
Reference Selection
Auto........................................................................... 3-3
Hand .......................................................................... 3-4
Reference Source...............................................3-6, 5-4, A-4
Relays, Digital Output................ 2-12, 2-14, 2-18, 7-3, A-15
RESET Key ...................................................................... 3-3
Resistance, Motor Line-to-Line..................................... A-11
Resonance ............................................5-27, 6-19, 6-20, A-9
REV Indicator .................................................................3-5
Reverse Operation.....................................................5-8, A-4
Prohibiting ............................................... 5-8, 6-17, A-4
Reverse Run/Stop command................................. 2-14, 2-18
Ride-thru, Momentary Power Loss........................................
............................................ 5-11, 5-39, A-5, A-19, B-3, C-4
“Right Arrow” Key...........................................................3-3
RS-485/422 .......................................................................5-5
Communication Wiring ............................................D-3
Control Circuit Terminals .............................. 2-14, 2-18
Parameters ..................................... 5-4, 5-32, A-4, A-18
Terminating Resistance....................................2-15, D-3
RTS Control Selection ...................................................A-18
Run Command
During Programing ............................................5-8, A-4
External, Troubleshooting .......................................6-16
Selection .............................................3-5, 4-6, 5-4, A-4
Source ........................................................ 3-4, 5-4, A-4
Terminals ....................................................... 2-14, 2-18
RUN Indicator........................................................... 3-1, 3-6
Running
Signal (output) .........................................................2-14
Stall Prevention during ..................................5-42, A-20
S
Safety Circuit .........................................4-3, 4-4, 2-14, A-14
Scaling Display
Digital Operator .............................................5-52, A-23
PI Setpoint .......................................................5-20, A-6
Schematic Diagram...............................2-9, 2-10, 2-17, 2-18
S-Curve Characteristic.....................................................A-7
SEQ........................................................................... 3-2, 3-5
Sequence Parameters .......................................................A-4
Serial Communications.......................................D-1 to D-14
Address .....................................................................D-4
Baud Rate ....................................... 6-9, A-18, D-2, D-4
Drive Node Address .................................................D-4
Parameters ............................................A-11, A-18, D-4
Run Command...........................................................5-4
Self-Diagnosis Function .........................................D-14
Station Address.........................................................D-5
Stop bits ....................................................................D-1
Serial Number ...................................................................1-3
Setpoint (PI Function)...........................................5-20, A-27
Boost Setting....................................................5-21, A-6
Display Scaling................................................5-17, A-6
Selection ................................................ 5-15, 5-19, A-6
Value ................................................................5-20, A-6
SHIFT/RESET Key ..........................................................3-3
Shield Wire Grounding ......................................... 2-12, 2-18
Shipping Damage..............................................................1-3
Short Circuit Protection, Branch...............................E-2, E-3
TM_E7_01_07182008.book Page 7 Wednesday, July 23, 2008 2:35 PM